YOKOGAWA PW441-10 热电偶输入和压力钳终端的组合
【功能描述】
●INFAT141的安装限制 (热电偶输入和压力钳终端的组合)。
钳形端子)的安装限制
为了保持参考结点的补偿精度(GS 34P02Q31-01E) ,请确保满足以下条件
条件。压力钳端子不应受到辐射热的影响。
-不要在安装了NFAT141的装置下面安装散热装置。
-不要将NFAT141安装在气流直接冲击的地方。
-不要将NFAT141安装在CPU模块(NFCP501/NFCP502) 、电源模块(NFPW44x) 旁边。
-在NFAT141旁边的可安装模块如下。当安装除以下I/0模块以外的其他模块时、
在每一侧留出一个空槽(一个或多个)。
可安装的模块: NFAT141, NFAR181, NFAV141, NFAV144
1通信模块的安裝限制
-每个FCN-500*多可以安装8个NFLR111/NFLR121.
-每个FCN-500*多可以安装8个NFLI11/NFLC121/NFLP121 (或*多8对NFLF111的双工)。
每个FCN-500*多可以安装8个NFLF111/NFLC121/NFLP121 (或8对NFLF111双工)。
1 I/0模块的安装限制
当您安装下列I/0模块时,请确保所需的功率量不超过电源模块的额定输出功率。
当您安装下列I/0模块时,请确保所需的电源容量不超过电源模块的额定输出功率。关于每个I/0模块所需的电源量
V
DC),请参考适用的一般规格。
1关于N2BU051、NFBU050或N2BU030的使用
- NFBU050是专门用于控制单元的。它不能作为扩展单元使用。
- SB总线重复模块不能安装在N2BU051、NFBU050或N2BU030.上。
- E2总线接口模块不能安装在NFBU050_上。
YOKOGAWA PW441-10 热电偶输入和压力钳终端的组合
● Installation limitations of the INFAT141 (combination of thermocouple input and pressure clamp terminal).
Clamp terminal) installation restrictions
In order to maintain the compensation accuracy of the reference node (GS 34P02Q31-01E), ensure that the following conditions are met
Conditions. Pressure clamp terminals should not be affected by radiant heat.
- Do not install cooling devices under devices with NFAT141 installed.
- Do not install NFAT141 in a direct airflow impact area.
Do not install NFAT141 next to CPU modules (NFCP501/NFCP502) or power modules (NFPW44x).
- The installable modules next to NFAT141 are as follows. When installing modules other than the following I/0 modules,
Leave an empty slot (one or more) on each side.
Installed modules: NFAT141, NFAR181, NFAV141, NFAV144
1 Restrictions on the installation of communication modules
- Each FCN-500* can install up to eight NFLR111/NFLR121.
- Each FCN-500* can install up to 8 NFLI11/NFLC121/NFLP121 (or up to 8 pairs of NFLF111 duplex).
Each FCN-500* can install up to 8 NFLF111/NFLC121/NFLP121 (or 8 pairs of NFLF111 duplex).
1 I/0 module installation restrictions
When you install the following I/0 modules, ensure that the required power does not exceed the rated output power of the PSU.
When you install the following I/0 modules, ensure that the required power capacity does not exceed the rated output power of the power module. About the amount of power required for each I/0 module
V
DC), please refer to applicable general specifications.
1 About the use of N2BU051, NFBU050 or N2BU030
- NFBU050 is used exclusively for control units. It cannot be used as an extension unit.
- SB bus repeat module cannot be installed in N2BU051, NFBU050, or N2BU030. Up.
- The E2 bus interface module cannot be installed on NFBU050_.
YOKOGAWA PW441-10 热电偶输入和压力钳终端的组合
【联系我们】
厦门雄霸电子商务有限公司
厦门市思明区吕岭路1733号创想中心2009-2010单元
联系人:珊妮
电话:18059884797
Copyright © 2022-2024 厦门雄霸电子商务有限公司 版权所有 备案号:闽ICP备14012685号-33