8440-2155 操作面板  延迟和关闭转换传输

型号：8440-2155

dtsc - 200 - 55 - b / K38

自动转换开关控制

DTSC-200是新ATS(自动转换开关)构建和改造的终极控制。一个完整的测量和保护包，它可以很容易地配置为公用事业对发电机，发电机对发电机，或公用事业对公用事业系统的开放，

伍德沃德的DTSC-200是新ATS(自动转换开关)构建和改造的终极控制。一个完整的测量和保护包，8440-2155它可以很容易地配置为公用事业到发电机，发电机到发电机，或公用事业到公用事业系统的开放，延迟，或封闭过渡转移与同步检查，以确保最顺利的转移。

8440-2155高端功能，如传输抑制、源优先级选择、负载卸载、电机负载断开、电梯预信号和发动机运动定时器，都是这款功能齐全、成本效益高的控制系统的标准配置。

8440-2155特点:

可配置为打开，延迟和关闭转换传输

可配置的效用到发电，发电机到发电机，和效用到效用应用程序

封闭过渡传输可以在< 100ms的时间内完成

同相监控(同步检查)

负载/无负载测试功能

发动机锻练(负荷/空载试验)程序，间隔完全可调

调峰方式

甩负荷

延长并行时间(对于耗时超过100ms的封闭转换传输)

禁止传输和/或重新传输

源优先级选择

电梯预转移和电机负载断开定时器

带有实时时钟的事件/警报日志系统

内部断路器联锁利用离散输入断路器位置检测

可自由配置的离散I/O，支持外部I/O扩展单元(例如Woodward ikd1)

RS-232, RS-485和CAN总线接口，用于远程控制和可视化目的

支持CANopen和Modbus RTU协议

PC和/或前显示配置

128x64像素图形LCD显示

LogicsManager提供可编程逻辑功能，消除继电器逻辑或PLC

真实有效值电压，电流和功率传感

用于电源可用性和断路器状态的led

Model: 8440-2155

dtsc - 200 - 55 - b / K38

Automatic transfer switch control

The DTSC-200 is the ultimate control for the construction and retrofitting of new ATS(Automatic Transfer Switch). A complete measuring and protection package, it can be easily configured for utility to generator, generator to generator, or utility to utility system open,

Woodward's DTSC-200 is the ultimate control for the construction and modification of the new ATS(Automatic Transfer Switch). A complete measuring and protection package, the 8440-2155 it can be easily configured for open, delayed, or closed transition transfers of utility to generator, generator to generator, or utility to utility system with synchronous checks to ensure the most smooth transfer.

8440-2155 High-end features such as transmission suppression, source priority selection, load offloading, motor load disconnection, elevator pre-signaling and engine motion timers are standard in this full-featured, cost-effective control system.

8440-2155 Features:

Can be configured to turn on, delay and turn off conversion transfers

Configurable utility to generation, generator to generator, and utility to utility applications

Closed transition transmission can be completed in < 100ms time

In-phase monitoring

Load/no load test function

Engine exercise (load/no-load test) program with fully adjustable intervals

Mode of peak regulation

Load shedding

Extended parallel time (for closed conversion transfers that take more than 100ms)

Transmission and/or retransmission is prohibited

Source priority selection

Lift pre-transfer and motor load off timer

Event/alert logging system with real-time clock

Internal circuit breaker interlocking uses discrete input circuit breaker position detection

Freely configurable discrete I/O with support for external I/O expansion units (e.g. Woodward ikd1)

RS-232, RS-485 and CAN bus interfaces for remote control and visualization purposes

Supports CANopen and Modbus RTU protocols

PC and/or front display configuration

128x64 pixel graphic LCD display

LogicsManager provides programmable logic capabilities that eliminate relay logic or PLCS

Real RMS voltage, current and power sensing

Leds for power availability and circuit breaker status