SPM-D2-11 同步器  具有模拟或离散偏置信号

SPM-D2-11是一款基于微处理器的同步器，专用于配备Woodward或者其它可兼容的速度控制器和自动化电压调节器的两相或三相交流发电机。SPM-D2-11同步器可使用模拟或离散输出偏置信号提供自动频率、相位和电压匹配。它整合了一个断路器同步、负载和功率因数控制或同步负载共享及发电机保护功能。这款同步器适用于广泛的原动机和发电机，因为可设置其控制信号以适应几种发电机组类型，包括从发动快速的柴油发动机到发动缓慢的燃气轮机。

SPM-D2-11 同步器现提供1种基本型号:

SP-D2-11:提供一相/两线电压测量，具有模拟或离散偏置信号、模拟有功和无功负载共

享线路和发电机保护。

特性

电压匹配的相位匹配或转差频率同步

具有Ⅰ级精确度的两相发电机和总线真实RMS电压感应·可选择操作模式，如SPM-A（运行、检查、允许和关闭)·同步检查和同步时间监控

·按需CB失效母线关闭

·两个模拟负载共享线路，用于负载/无功功率共享·电源并行运行中的有功功率和功率因数控制

·孤网运行中的电压和频率控制

根据参数(2个值）或通过0/4 到20 mA模拟输入的发电机真实功率设置点·柔性卸载和继电器输出的功率限制值

·控制输出:离散提高/降低所有变型中的速度和电压或模拟信号（电压、电流和PWM)·发电机一相CT感应，具有功率、过载、电压和频率保护

用于操作、警报和测量值显示和参数化的两线清晰液品显示屏·前部配有同步指示器，可指示断路器状态/控制活动

参数的多级密码保护

可通过USB 配置的Woodward ToolKitTM软件.两种内置语言:英文、德文

SPM-D2-11 同步器  具有模拟或离散偏置信号

The SPM-D2-11 is a microprocessor-based synchronizer designed for two - or three-phase alternators equipped with Woodward or other compatible speed controllers and automated voltage regulators. The SPM-D2-11 synchronizer provides automatic frequency, phase, and voltage matching using analog or discrete output bias signals. It integrates a circuit breaker synchronization, load and power factor control or synchronous load sharing and generator protection functions. This synchronizer is suitable for a wide range of prime movers and generators because its control signals can be set to suit several generator types, from fast diesel engines to slow gas turbines.

The SPM-D2-11 synchronizer is now available in one basic model:

SP-D2-11: Provides one phase/two line voltage measurement with analog or discrete bias signals, analog active and reactive loads

Enjoy line and generator protection.

peculiarity

Phase matching or slip frequency synchronization for voltage matching

Two-phase generator and bus real RMS voltage sensing with Class I accuracy · Selselable operating modes such as SPM-A (Run, Check, Allow and Off)· Sync check and sync time monitoring

· CB failure bus is closed on demand

· Two analog load sharing lines for load/reactive power sharing · Active power and power factor control in parallel power supply operation

· Voltage and frequency control in isolated network operation

Set the point · Flexible unloading and relay output power limits based on the parameters (2 values) or the generator real power input through 0/4 to 20 mA simulation

· Control output: discretely increase/decrease the speed and voltage or analog signal (voltage, current and PWM) in all variants · Generator one-phase CT induction with power, overload, voltage and frequency protection

A two-line clear liquid display for operation, alarm and measurement display and parameterization with a synchronous indicator on the front to indicate circuit breaker status/control activity

Parameter multi-level password protection

Woodward Tools ™ software configurable via USB. Two built-in languages: English and German