2N3A8130-A TOSHIBA 模拟输出模块

2N3A8130-A TOSHIBA 模拟输出模块

2N3A8130-A TOSHIBA 模拟输出模块

2N3A8130-A东芝模块TOSHIBA 2N3A8130-A，N3A3620-B,2N3A8130-A,2N3A3120-D东芝模块，东艺IGCT模块东芝集团创立于1875年,致力于为人类和地球的明天而努力奋斗,力争成为能创造丰富的价值并能为全人类的生活、文化作贡献的企业集团,东芝集团业务领域包括数码产品、电子元器件、社会基础设备、家电等东芝模块TOSHIBA 2N3A3110-C 安装调试确保2N3A3110-C 在设定地址前完成电力排线,2N3A3110-C 先送内机电源再送外机电源，如果在开启室内机之前开启室外机，外机P.C.板上7段显示码会显示E19，直至开启室内机电源。

自动寻址可能会花费十分钟时间(正常为5分钟)自动寻址要求在室外机操作。(仅打开电源不能自动寻址。)。自动寻址会使用到室外机P.C.板界面上的SW15按键1.首先送上室内机电源，然后再送室外机电源。2电源送上后确认室外主机P.C.板界面上7段显示板显示 U.1.L08(此时U.1,闪)3,按下SW15(7段显示板有了变化松开，正常3秒左右)开始自动寻址(通常为5分钟)。4.7段显示指示Auto1然后Auto2到Auto3指示 U.1.-(U.1.闪)开始在显示器上闪烁后。闪烁停止显示器显示 U.1.-(U.1.灯常亮)设定完成。调试前准备工作1.确定保压正常，系统无漏。2. 算好铜管每米追加量与机组的修正量。3.管与气管阀门打开。

2N3A8130-A TOSHIBA 模拟输出模块

TOSHIBA 2N3A8130-A, N3A3620-B,2N3A8130-A, 2N3A33A3120-D Toshiba module, TOSHIBA Group, founded in 1875, is committed to working hard for the future of mankind and the earth, and strives to become an enterprise group that can create rich value and contribute to the life and culture of all mankind. Toshiba Group's business areas include digital products, electronic components, social infrastructure equipment, home appliances and other Toshiba modules Toshiba 2N3A3110-C Installation and commissioning Ensure that the 2N3A3110-C is routed before the address is set. The 2N3A3110-C sends the internal power supply before the external power supply. If the outdoor unit is started before the indoor unit is started, the external unit is P.C. The seven-segment display code on the board displays E19 until the indoor unit is powered on.

Auto addressing may take up to 10 minutes (normal is 5 minutes) Auto addressing requires an outdoor unit operation. (Power on alone does not automatically address.) . Automatic addressing uses the SW15 button on the outdoor unit P.C. panel interface. 1. Send the indoor unit power supply first, and then the outdoor unit power supply. 2 After the power supply is sent, confirm that the 7-segment display board on the outdoor host P.C. board interface displays U.1.L08(at this time, U.1 flashes)3, press SW15(the 7-segment display board changes and releases, normal for about 3 seconds) to start automatic addressing (usually 5 minutes). Segment 4.7 shows indicating Auto1 and then Auto2 through Auto3 indicating U.1.-(U.1. Flash) after it starts flashing on the monitor. Blinking Stop display U.1.-(U.1. Light on) Setting complete. 1. Ensure that the pressure retention is normal and there is no leakage in the system. 2. Calculate the additional amount of copper pipe per meter and the correction amount of the unit. 3. Pipe and gas pipe valves open.

2N3A8130-A TOSHIBA 模拟输出模块