140CPU11303 Schneider 处理器

主要信息

产品系列

Modicon Quantum自动化平台

产品类型：处理器

软件名称：ProWORX 32Concept

处理器名称：80186

数学协处理器：无

补充信息

时钟脉冲频率：20 MHz

内存说明：内部 RAM 368 kB

1K指令的精确时间：0.3...1.4 ms LL984

监视时钟：250 ms

时钟误差：+/-8 s/天在...上 0...60 °C

输入输出字节：30 l/32O分布式64 l64O最大本地64 l64 O远程

输入输出字节/网络：500 /500O分布式

降低/网络：63分布式

分支数：31远程

网络数：2远程3分布式

电池类型：锂7 uA 210 uA

蓄电池容量：1.2 Ah

电池使用寿命：10年

端口量：1串口Modbus RS2321 Modbus Plus

通讯模块处理器：2 NOM, NOE,CR,NMS

开关功能：无钥匙开关

标识：CE

需求总线电流：790 mA

模块分类：标准

净重：0.3 kg

环境

产品认证：FM,1类,2分类cUL

符合标准

UL 508

CSA C22.2 No 142

抗静电放电：4 kV触点符合IEC 801-28 kV广播符合IEC 801-2

抗电磁域：10 V/m 80...2000 MHz符合IEC 801-3

运行温度：0...60 c

贮存环境温度：-40...85°C

相对湿度：95%无冷凝

工作海拔：<= 5000 m

4OCPU11303使用的常见问题

问题1:4OCPU11303使用IEC编程很容易就报内存不足?

解决方法:140CPU11303对应有两个固件:1个对应140CPU11303，1个对应

140CPU11303S。当使用对应140CPU11303固件时，CPU既支持LL984，又支持IEC，但IEC容量会很小。如果用户确定自己的应用完全是IEC应用，请将CPU固件更新为

140CPU11303S固件，该操作后CPUIEC编程容量较原来会有极大的扩大。具体的操作:Quantum 11303固件更新为只支持IEC编程方式;在Concept软件中将CPU的型号由

140CPU11303修改为140CPU11303S。

问题2:将140CPU11303 PVO6固件刷为140CPU11303S，下载程序，运行正常，但停电后再供电,Run灯灭，IO模块Active灯灭，无法启动CPU且报错0004，再次下载程序后OK

解决方法:对于140CPU11303固件更新为140CPU11303S，下载程序并正常启动运行CPU后操作CPU停电后重新供电，正常的情况是CPU停电前是什么状态，重新供电后依然是什么状态，标题描述的现象显然是不正常的，我们针对另外一个新的140CPU11303 PVO6的CPU进行与标题描述完全相同的操作，没有复现出标题描述的故障现象，据此判断该故障现象为个体故障，而非批次故障，与140CPU11303硬件版本升级至PVO6以及PV06对应的固件更新文件Bug无关。另外，在CPU停机的状态下，所有IO模块上Active灯灭，这是正常现象。

问题3:140CPU11303下载程序时报错,显示的错误代码为“OLI-21707",但如果仅改变配置,其他程序不变,然后再下载到140CPU43412A中时,却又—切正常

解决方法:出现上述错误情况的原因是用户编程的Project中含有涉及浮点操作的EFB,对于140CPU43412A，它在不作任何处理的情况下即可支持浮点运算,而140CPU11303,如不作任何处理不支持浮点运算,所以如果在程序下载前没有下载相应的loadable文件,则将该

Project下载到140CPU11303中时会始终报错,但下载到140CPU43412A中时,却会一切正常.解决办法是在程序下载前先下载名为"EMUQ"的loadable文件。

140CPU11303 Schneider 处理器

Main information

Product series

Modicon Quantum automation platform

Product type: Processor

Software name: ProWORX 32Concept

Processor name: 80186

Mathematical coprocessor: None

Supplementary information

Clock pulse frequency: 20 MHz

Memory Description: Internal RAM 368 kB

Exact time of 1K instruction: 0.3... 1.4 ms LL984

Monitor clock: 250 ms

Clock error: +/-8 s/ day in... Top 0... 60 °C

Input/Output bytes: 30 l/32O Distributed 64 l64O Max local 64 l64O remote

Input/Output byte/Network: 500/500O distributed

Reduced/Network: 63 distributed

Number of branches: 31 remote

Number of networks: 2 remote 3 Distributed

Battery type: Lithium 7 uA 210 uA

Battery capacity: 1.2Ah

Battery life: 10 years

Port quantity: 1 Serial port Modbus RS2321 Modbus Plus

Communication module processor: 2 NOM, NOE,CR,NMS

Switch function: keyless switch

Mark: CE

Required bus current: 790 mA

Module classification: Standard

Net weight: 0.3 kg

environment

Product certification: FM, Class 1, Class 2 cUL

Meet the standard

UL 508

CSA C22.2 No 142

Antistatic discharge: 4 kV contacts compliant with IEC 801-28 kV broadcast compliant with IEC 801-2

Anti-electromagnetic domain: 10 V/m 80... 2000 MHz conforms to IEC 801-3

Operating temperature: 0... 60 c

Storage ambient temperature: -40... 85°C

Relative humidity: 95% non-condensing

Working altitude: <= 5000 m

4OCPU11303 Frequently Asked Questions

Q.1 :4 Is it easy for OCPU11303 to report low memory using IEC programming?

Solution: The 140CPU11303 pair should have two firmware versions: one for 140CPU11303 and one for 140CPU11303

140CPU11303S. If the 140CPU11303 firmware is used, the CPU supports both LL984 and IEC, but the IEC capacity is small. If the user determines that his application is entirely IEC application, update the CPU firmware to

140CPU11303S firmware. After this operation, the CPUIEC programming capacity will be greatly expanded. Specific operations :Quantum 11303 firmware is updated to support IEC programming only; In the Concept software, the model of the CPU is replaced by

140CPU11303 Change the value to 140CPU11303S.

Problem 2: Brush the firmware of the 140CPU11303 PVO6 to 140CPU11303S, download the program, and the program runs normally. However, after the power is off, the Run indicator and the Active indicator of the I/O module are off, the CPU cannot be started, and an error 0004 is reported

Solution: For the 140CPU11303 firmware update to 140CPU11303S, download the program and run the CPU normally after the operation of the CPU power outage after the power supply, the normal situation is the CPU power before the state, after the power supply is still what state, the phenomenon described in the title is obviously abnormal. We carried out the same operation as the title description for another new 140CPU11303 PVO6 CPU, and did not repeat the fault described in the title. According to this, we can judge that the fault is an individual fault rather than a batch fault. This is not related to the Bug in the firmware update file corresponding to the hardware upgrade from 140CPU11303 to PVO6 or PV06. In addition, when the CPU is stopped, the Active indicator on all I/O modules is off. This is normal.

Problem 3: 00CPU11303 program download error, display error code "OLI-21707", but if only change the configuration, other programs remain unchanged, and then download to 140CPU43412A, it is not normal

Solution: The cause of the above error situation is that the user programming Project contains EFB involving floating point operations, for 140CPU43412A, It supports floating-point operations without any processing, while the 140CPU11303 does not support floating-point operations without any processing, so if the corresponding loadable file is not downloaded before the program is downloaded, it will be used

When the Project is downloaded to 140CPU11303, it will always report an error, but when it is downloaded to 140CPU43412A, everything will be fine. The workaround is to download the loadable file named "EMUQ" before the program downloads.