5880-PC1025 Rolls Royce 涡扇发动机 /高性能的发动机

描述

品牌:Rolls Royce

型号:5880-PC1025

名称：转向PCB模块

颜色：标准

工作温度：0至85摄氏度

应用：工业

重量：0.18千克

产地:USA

质保:—年

Rolls Royce 5880-PC1025是一款高性能的发动机，适用于多种应用领域。

规格

类型:涡扇发动机

推力:25,000磅

长度:287英寸

直径:94英寸

干重:7,100磅

5880-PC1025对于本地节点，反射内存板显示为共享内存。任何级别的软件(包括应用程序本身)都可以将数据写入内存或从内存中读取数据。写入一个节点的反射内存的数据由网络硬件传输到所有其他节点,并放置在这些节点的反射内存板上的相同地址中。这种数据传输无需任何节点上的处理器参与即可完成。通过该系统，网络上的所有节点都具有可立即访问的共享数据的本地副本。

特征:

5880-PC1025支持具有I/O总线功能版本16及更高版本的紧凑型登录处理器附加指令创建UDT,为I/O、状态和控制数据提供逻辑定义模块配置备份在压缩日志项目(ACD文件)

模块充当协处理器，减少对 PLC扫描时间的影响支持多达240字的/O数据

处理器控制器标签中提供诊断数据,可根据节点运行状况做出决策附加配置文件支持,改进了在CompactLogix系统中的集成，应用程序端口可配置为模块总线主站或模块总线从站作为模块总线主站,支持多达30个模块。

5880-PC1025抗干扰与外部互锁当PLC输出带感性负载，负载断电时会对PLC的输出造成浪涌电流的冲击，为此，对直流感性负载应在其旁边并接绫流二极管，对交流感性负载应并接浪涌吸收电路，可有效保护PLC。当两个物理量的输出在PLC内部已进行软件互锁后，在PLC的外部也应进行互锁，以加强系统的可靠性。

"GOM “点的选择不同的PLC产品，其“COM”点的数量是不一样的，有的一个“COM”点带8个输出点，有的带4个输出点，也有带2个或1个输出点的。当负载的种类多，且电流大时，采用一个“COM”点带1—2个输出点的PLC产品;当负载数量多而种类少时，采用一个“COM”点带4—8个输出点的PLC产品。这样会对电路设计带来很多方便，每个“COM”点处加一熔丝，1—2个输出时加2A的熔丝，4—8点输出的加5—10A的溶丝，因PLC内部一般没有熔丝。

5880-PC1025 Rolls Royce 涡扇发动机 /高性能的发动机

Description

Brand :Rolls Royce

Model :5880-PC1025

Name: Turn to PCB module

Color: Standard

Operating temperature: 0 to 85 degrees Celsius

Application: Industry

Weight: 0.18 kg

Origin :USA

Warranty: - year

The Rolls-Royce 5880-PC1025 is a high-performance engine suitable for a wide range of applications. The following is the product specification, technical description and product parameters.

specification

Type: Turbofan engine

Thrust :25,000 pounds

Length :287 inches

Diameter :94 inches

Dry weight :7,100 LBS

5880-PC1025 For local nodes, the reflected memory board appears as shared memory. Any level of software, including the application itself, can write data to or read from memory. Data written to the reflected memory of one node is transmitted by the network hardware to all other nodes and placed at the same address on the reflected memory boards of those nodes. This data transfer can be done without the involvement of processors on any node. With this system, all nodes on the network have a local copy of the shared data that is instantly accessible.

Features:

5880-PC1025 Supports compact logon processors with I/O bus capabilities version 16 and later Additional instructions Create UDTs to provide logical definition for I/O, status and control data Module Configuration Backup in Compressed log Project (ACD file)

The module acts as a coprocessor, reducing the impact on PLC scan times and supporting up to 240 words /O of data

Diagnostic data is available in the processor controller label to make decisions based on node health Additional profile support improves integration in the CompactLogix system, application ports can be configured as module bus master or module bus slave as module bus master, supporting up to 30 modules.

5880-PC1025 Anti-interference and external interlock when the PLC output with inductive load, load power will cause surge current impact on the PLC output, therefore, the DC inductive load should be next to it and connected to the current diode, the AC inductive load should be connected to the surge absorption circuit, which can effectively protect the PLC. When the output of two physical quantities has been interlocked inside the PLC, it should also be interlocked outside the PLC to enhance the reliability of the system.

"GOM "point selection of different PLC products, the number of" COM "points is not the same, some a" COM "point with 8 output points, some with 4 output points, there are 2 or 1 output points. When the types of load are many and the current is large, a PLC product with a "COM" point and 1-2 output points is used; When the number of loads is large and the types are small, a PLC product with 4-8 output points and a "COM" point is used. This will bring a lot of convenience to the circuit design, each "COM" point plus a fuse, 1-2 output plus 2A fuse, 4-8 point output plus 5-10A melt wire, because there is generally no fuse inside the PLC.