BERGER LAHR-VRDM564--50LHA  脉冲/方向 步进电机控制器

型号：BERGER LAHR-VRDM564--50LHA

产品参数:

电源电压:24-48VDC

·最大输出电流:5A

·步进角度:1.8°

步进模式:全步进、半步进

控制方式:脉冲/方向、双向脉冲

·保护等级:IP20

ERGERLAHR VRDM5645O0LHA是一款高性能步进电机，专为各种工业应用而设计。它提供精确的控制和精度，使其非常适合用于制造，加工和其他苛刻的环境。

产品规格

—步进角度:1.8度

-保持扭矩:4.5 Nm

-电流/相位:5a

—电压:200vac

BERGERLAHRVRDM564/50LHA逻辑8通道模块使用计算机控制系统的DCS过程报警分级控制技术中的每一项参数都需要严格设定和掌控，出现参数过高和过低的现象都会对现场造成难以估量的损失，要求在设置报警参数时通过严格的数据分析实现报警参数的准确性和规范性。

在设置报警方式时可采用窗口弹出的方式，也可采用语音报警的方式，有效提高工作人员的关注度，为工作人员提供佳的解决时间，避免出现更加严重的事故和损失。

●弹窗式报警方式

设置弹窗式报警时，操作人员通过对现场的监测和控制实现报警过程的准确性，窗口弹出的设置方式要在控制显示页面的中心位置，方便工作人员一时间关注到报警的位置和出现问题的方向，为操作人员提供更多的准备时间，以便有效解决过程中出现的问题。

BERGER LAHR-VRDM564--50LHA  脉冲/方向 步进电机控制器

Model: BERGER LAHR-VRDM564--50LHA

Product parameters:

Power supply voltage :24-48VDC

· Maximum output current :5A

· Stepping Angle :1.8°

Step mode: full step, half step

Control mode: pulse/direction, bidirectional pulse

· Protection level :IP20

ERGERLAHR VRDM5645O0LHA is a high performance stepper motor designed for a variety of industrial applications. It offers precise control and precision, making it ideal for use in manufacturing, processing and other demanding environments.

Product specification

- Step Angle :1.8 degrees

- Holding torque: 4.5Nm

- Current/phase :5a

- Voltage :200vac

BERGERLAHRVRDM564/50LHA logic 8-channel module using the DCS process alarm hierarchical control technology of the computer control system each parameter needs to be strictly set and controlled, and the phenomenon of too high and too low parameters will cause incalculable losses to the scene. It is required to realize the accuracy and standardization of alarm parameters through strict data analysis when setting alarm parameters.

When setting the alarm mode, a pop-up window can be used, or a voice alarm can be used to effectively improve the attention of the staff, provide the best solution time for the staff, and avoid more serious accidents and losses.

● Pop-up alarm mode

When the pop-up alarm is set, the operator realizes the accuracy of the alarm process by monitoring and control of the scene. The setting mode of the pop-up window should be in the center of the control display page, so as to facilitate the staff to pay attention to the location of the alarm and the direction of the problem, and provide more preparation time for the operator to effectively solve the problem in the process.