UTX-1000A 可实现自动化系统

产品描述

UTX-1000A MECS控制器可实现自动化系统中的各种操作控制功能。

特征

可编程逻辑控制器（PLC）技术，可实现自动化控制。

彩色液晶触摸屏，操作简单方便。

支持多种输入和输出信号，可与各种机械和设备配合使用。

可实现远程监控和控制，方便操作和维护。

UTX-1000A MECS操作控制器是一款高性能的操作控制器，能够灵活适应各种自动化系统的要求。该控制器采用先进的控制算法，具有高速、高精度和高可靠性的特点，能够满足复杂自动化系统的控制需求。

UTX-1000A MECS操作控制器采用先进的嵌入式系统和通用I/O接口，可实现多种输入输出信号的采集和控制，包括数字量输入输出、模拟量输入输出和PWM输出等。该控制器还支持多种通信协议，包括CAN总线、Modbus、以太网等，可与其他设备进行数据交换和通信。

UTX-1000A MECS操作控制器是一种高性能控制器，采用可编程逻辑控制器（PLC）技术，可实现工程机械和设备的自动化控制。它具有7英寸彩色液晶触摸屏和多种输入和输出信号，支持远程监控和控制，方便操作和维护。

应用领域

UTX-1000A MECS操作控制器广泛应用于各种工程机械和设备，如挖掘机、装载机、铲车、起重机等。

测量主轴实际转速将机床锁住开关放在接通位置，用手动数据输入指令，进行主轴任意变档，变速试验，测量主轴实际转速，并观察主轴速度显示值，调整其误差应限定在5％之内。进行转塔或刀座的选刀试验其目的是检查刀座或正、反转和定位精度的正确性。功能试验根据定货的情况不同，功能也不同，可根据具体情况对各个功能进行试验。为防止意外情况发生，最好先将机床锁住进行试验，然后再放开机床进行试验。

方法：

根据经验判断，确定两次采样允许的最大偏差值（设为A）

每次检测到新值时判断：

如果本次值与上次值之差<=A，则本次值有效

如果本次值与上次值之差>A，则本次值无效，放弃本次值，用上次值代替本次值。可以有效克服因偶然因素引起的脉冲干扰。

UTX-1000A 可实现自动化系统

Product description

The UTX-1000A MECS controller enables a variety of operational control functions in automated systems.

trait

Programmable logic controller (PLC) technology can realize automatic control.

Color LCD touch screen, easy to operate.

Support a variety of input and output signals, can be used with a variety of machinery and equipment.

Can realize remote monitoring and control, easy operation and maintenance.

The UTX-1000A MECS Operation Controller is a high-performance operation controller that can be flexibly adapted to the requirements of various automation systems. The controller adopts advanced control algorithm, has the characteristics of high speed, high precision and high reliability, and can meet the control requirements of complex automation systems.

UTX-1000A MECS operating controller adopts advanced embedded system and universal I/O interface, which can realize the acquisition and control of various input and output signals, including digital input and output, analog input and output and PWM output. The controller also supports a variety of communication protocols, including CAN bus, Modbus, Ethernet, etc., and can exchange data and communicate with other devices.

The UTX-1000A MECS Operating controller is a high-performance controller that uses programmable logic controller (PLC) technology to automate the control of construction machinery and equipment. It has a 7-inch color LCD touch screen and a variety of input and output signals, support remote monitoring and control, easy operation and maintenance.

Application field

The UTX-1000A MECS operating controller is widely used in a variety of construction machinery and equipment, such as excavators, loaders, forklifts, cranes, etc.

Measure the actual speed of the spindle put the lock switch on the machine tool in the on position, enter the instructions with manual data, carry out the spindle arbitrary shift, speed change test, measure the actual speed of the spindle, and observe the displayed value of the spindle speed, and adjust its error should be limited to 5%. The purpose of the tool selection test of the turret or the tool holder is to check the correctness of the tool holder or the forward, reverse and positioning accuracy. Function test according to the order of the situation is different, the function is different, can be tested according to the specific situation of each function. In order to prevent accidents, it is best to lock the machine first for testing, and then release the machine for testing.

How:

Based on experience, determine the maximum deviation allowed for two samples (set to A).

Each time a new value is detected:

If the difference between the current value and the previous value <=A, the current value is valid

If the difference between this value and the last value is greater than A, the value is invalid, and the value is abandoned and replaced with the last value. It can effectively overcome the pulse interference caused by accidental factors.