57C430A  处理器模块    有两个 RS-232 母头通信端口

型号：57C430A

类别：处理器模块

成色：全新，非全新

质保：一年

重量：8磅

品牌：Reliance

主要特点

CPU 速度: 0.45 MHz

内存: 256 KB

I/O 点数: 最大 256 点

通信接口: RS-232、RS-485、CAN 等

支持多种扩展模块

关于57C430

57C430 是由 Reliance Electric 创建的处理器模块。根据该模块的生产年份，它也可能由 Asea Brown Boveri 或 Baldor Reliance 销售。该模块不再从原始公司获得任何支持，并且可能有点难以找到。AX Control 确实尽一切努力将此部件作为翻新或新的剩余库存部件保持库存。

57C430是一款AutoMax 6010处理器模块。该处理器旨在安装在 AutoMax 机架上，然后控制机架上的所有其他模块。根据机架的大小，您可以选择机架上只有一个处理器。您还可以选择在同一机架上放置最多四个。

为了能够正确使用57C430，它有两个系统要求。系统需要具有 256k 的 RAM 奇偶校验和 8mHZ 的 CPU 速度。此外，对于可以将 57C430 放置在存储架上的位置，也有要求。它只能插入机架上的 0-4 个插槽。如果您使用多个处理器，则必须将其中一个处理器放入该插槽中，或者必须使其完全打开。

57C430 有两个 RS-232 母头通信端口。其中一个标记为 PORT A，另一个标记为 PROGRAMMER/PORT B。有两个标记为 FAULT CODE 的 LED。其中两个 LED 是绿色的，标记为 BAT。好了，好了。蝙蝠。如果 RAM 备用电池已消耗，OK 指示灯将停止发光。有两个 7 段错误代码指示器，分别标记为第 1 和第 2 个。

Model: 57C404B

Category: Processor module

Finish: New, not new

Warranty: One year

Weight: 8 pounds

Brand: Reliance

Main feature

CPU speed: 0.45MHz

Memory: 256 KB

I/O count: Maximum 256 points

Communication interface: RS-232, RS-485, CAN, etc

Supports a variety of extension modules

About 57C430

The 57C430 is a processor module created by Reliance Electric. Depending on the year of production of the module, it may also be marketed by Asea Brown Boveri or Baldor Reliance. The module no longer receives any support from the original company and can be a little hard to find. AX Control does make every effort to keep this part in stock as a refurbished or new surplus stock part.

The 57C430 is an AutoMax 6010 processor module. The processor is designed to be mounted on an AutoMax rack and then control all other modules on the rack. Depending on the size of the rack, you can choose to have only one processor on the rack. You can also choose to place up to four on the same rack.

In order to be able to use the 57C430 properly, it has two system requirements. The system requires 256k of RAM parity and a CPU speed of 8mHZ. In addition, there are requirements for where the 57C430 can be placed on a storage rack. It can only be inserted into 0-4 slots on the rack. If you use multiple processors, one of them must be put into the slot, or it must be left fully open.

The 57C430 has two RS-232 female communication ports. One of these is labeled PORT A and the other is labeled PROGRAMMER/PORT B. There are two leds labeled FAULT CODE. Two of the leds are green and labeled BAT. All right, all right. bat. If the RAM backup battery is depleted, the OK indicator will stop shining. There are two 7-paragraph error code indicators, labeled 1st and 2nd.