PCI-6733 模拟输出设备 帮助用户创建个性化测量方案来测试其创新的设计

PCI-6733是一款16位8通道1MS/s模拟输出设备。

PCI-6733高速模拟输出，性能优越可靠，可满足多数应用的要求。PCI-6733提供了8路模拟输出通道，每条通道均有最高输出速度1MS/s，16位分辨率以及数字触发。该板卡采用RTSI总线，可同步其他数据采集，运动和视觉产品，从而帮助用户创建个性化测量方案来测试其创新的设计

16位8通道1 MS/s模拟输出设备‑—PCI-6733是一款高速模拟输出设备，专为激励响应测试（包括声学失真测试）和仿真（如三相电源仿真）等控制和波形输出应用提供多通道同步更新。此外，该设备还提供了8条5 V TTL/CMOS数字I/O线；两个24位20 MHz计数器/定时器；和数字触发和外部时钟功能。PCI-6733可以替代几种仪器，包括独立的比例积分微分(PID)控制器、低速任意波形发生器和函数发生器。

National Instruments PCI-6733 模拟输出设备

National Instruments PCI-6733（部件号：778510-01）是一款1 MS/s、8通道、16位模拟输出器件。除了各种标准功能外，该型号还具有声波形生成和采集功能。借助 NI PCI-6733， 用户 可以 创建 常见 和 复杂 波形， 同时 控制 每 个 通道 的 每 个 数据 点。该模型允许用户将每个DAC连接到器件内部基准或外部基准信号，通过AO EXT REF（外部基准引脚）包含在其I/O连接器中。但是，用户不能施加超出 ±11 伏 AO GND 允许范围的任何信号。通过 AO EXT REF 可以净降低输出电压范围，从而在修改后的范围内带来更高的分辨率。该设备配有一个 68 针公头 SCSI-II I/O 连接器。它具有 8 条数字 I/O 线，兼容 5 V TTL/CMOS，输入和输出缓冲器各为 2,000 字节，以及 2 条计数器/定时器 I/O 线，频率为 20 MHz，分辨率为 24 位。此外，它的功率要求为1.25 A（典型值）和1.8 A（最大值）（在+5 VDC）、125 mA（典型值）和250 mA（最大值）（在+3.3 VDC时）。

PCI 6733 National Instruments 模拟输出设备带有 8 行双向数字输入/输出信号，具有可单独控制的功能和方向控制、快速波形生成和采集功能。PCI-6733 NI 上的 DIO 端子可通过本设备中包含的标准 I/O 连接器进行访问;DIO 端子命名为 P0。<0...7>。借助 NI PCI 6733 模拟 输出 设备， 用户 可 将 每 条 DIO 线 用作 静态 数字 输入 线 或 数字 输出 线。静态数字I/O线是用于监测或控制数字信号的可计数解决方案。但是，静态数字输入线的整个采样和静态数字输出线的更新都是通过软件控制的。

PCI-6733 模拟输出设备 帮助用户创建个性化测量方案来测试其创新的设计

The PCI-6733 is a 16-bit 8-channel 1MS/s analog output device.

PCI-6733 high-speed analog output, superior and reliable performance, can meet the requirements of most applications. The PCI-6733 provides eight analog output channels, each with a maximum output speed of 1MS/s, 16-bit resolution, and digital triggering. The board uses the RTSI bus to synchronize other data acquisition, motion and vision products, helping users create personalized measurement solutions to test their innovative designs

16-bit 8-channel 1 MS/s analog Output Device ‑ - The PCI-6733 is a high-speed analog output device designed to provide multi-channel synchronous updates for control and waveform output applications such as excitation response testing (including acoustic distortion testing) and simulation (such as three-phase power simulation). In addition, the device offers eight 5V TTL/CMOS digital I/O lines; Two 24-bit 20 MHz counters/timers; And digital trigger and external clock functions. The PCI-6733 can replace several instruments, including independent proportional integral differential (PID) controllers, low-speed arbitrary waveform generators, and function generators.

National Instruments PCI-6733 Analog output device

The National Instruments PCI-6733 (Part number: 778510-01) is a 1 MS/s, 8-channel, 16-bit analog output device. In addition to various standard features, this model also features acoustic waveform generation and acquisition. With the NI PCI-6733, users can create common and complex waveforms while controlling every data point in every channel. This model allows users to connect each DAC to either an internal reference or an external reference signal, which is included in its I/O connector via AO EXT REF (external reference pin). However, the user cannot apply any signal beyond the allowable range of ±11 volt AO GND. The AO EXT REF allows a net reduction in the output voltage range, resulting in higher resolution in the modified range. The device is equipped with a 68-pin male SCSI-II I/O connector. It features eight digital I/O lines compatible with 5 V TTL/CMOS with input and output buffers of 2,000 bytes each, and two counter/timer I/O lines at 20 MHz with 24-bit resolution. In addition, it has power requirements of 1.25 A (typical value) and 1.8 A (maximum value) (at +5 VDC), 125 mA (typical value) and 250 mA (maximum value) (at +3.3 VDC).

The PCI 6733 National Instruments analog output device comes with 8 lines of bi-directional digital input/output signals with individually controllable functionality and direction control, fast waveform generation and acquisition. DIO terminals on the PCI-6733 NI are accessible via standard I/O connectors included with this device; The DIO terminal is named P0. < 0... 7>. With the NI PCI 6733 analog output device, users can use each DIO line as a static digital input line or a digital output line. Static digital I/O lines are a countable solution for monitoring or controlling digital signals. However, the entire sampling of the static digital input line and the updating of the static digital output line are controlled by software.