PCI-6713 高速模拟输出设备 可为控制和波形输出应用提供同步的多通道更新

PCI-6713 模拟输出设备,12位8通道1 MS/s模拟输出设备—PCI‑6713是一款高速模拟输出设备，可为控制和波形输出应用（如激励响应、电源控制、高速、确定性控制和传感器/信号仿真）提供同步的多通道更新。 此外，该设备还提供了8条5 V TTL/CMOS数字I/O线；两个24位20 MHz计数器/定时器；和数字触发和外部时钟功能。

National Instruments PCI-6713 模拟输出设备

National Instruments PCI-6713（部件号：777741-01）是一款基于PCI的多功能模拟输出、定时输入/输出和DIO器件，具有8个模拟输出通道、2个计数器和8个数字输入/输出通道。该设备设计为完全作为即插即用单元运行。对于其 8 个模拟输出通道中的每一个，都提供了一个专用的 12 位数模转换器，可提供高达 1 MS/秒的电压输出更新速率。该型号还具有 8 条兼容 5 V TTL/CMOS 的数字输入/输出线。它有 3 个 DMA 通道，具有 scather-gather DMA 模式，一个 5V PCI 主从总线接口。

该器件中包含的计数器/定时器数量为 2 个，分辨率为 24 位，频率为 20 MHz、100 kHz。它有 1 个频率缩放器，基本时钟为 10 MHz、100 kHz。该器件的最大工作电压为 ±11V，CAT 1 用于通道对地隔离;±22 V，CAT 1 用于通道间。PCI 6713 National Instruments 还支持基于硬件的数字触发。该型号配备了DAQ-STC，可选择逻辑电平、PFI线路和频移键控。此外，DAQ-STC还带来了各种缓冲操作，如上/下控制、等效时间采样、单脉冲生成、脉冲序列生成、缓冲周期和半周期测量。NI 设备 配备 了 一个 68 针 公 头 SCSI-II I/ O 连接器。

PCI-6713是一款高速模拟输出设备。

PCI-6713具有以下特点：

为控制和波形输出应用（如激励响应、电源控制、高速、确定性控制和传感器/信号仿真）提供同步的多通道更新。

提供8条5V TTL/CMOS数字I/O线。

提供两个24位20MHz计数器/定时器。

提供数字触发和外部时钟功能。

可替代几种仪器，包括独立的比例积分微分（PID）控制器、低速任意波形发生器和函数发生器等。

PCI-6713 高速模拟输出设备 可为控制和波形输出应用提供同步的多通道更新

PCI-6713 Analog Output Device, 12-bit, 8-channel,1 MS/s analog output device - PCI-6713 is a high-speed analog output device that provides synchronous multi-channel updates for control and waveform output applications such as excitation response, power control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device offers eight 5V TTL/CMOS digital I/O lines; Two 24-bit 20 MHz counters/timers; And digital trigger and external clock functions.

National Instruments PCI-6713 Analog output device

The National Instruments PCI-6713 (Part number: 777741-01) is a multi-function PCI-based analog output, timing input/output, and DIO device with eight analog output channels, two counters, and eight digital input/output channels. The device is designed to operate entirely as a plug and play unit. For each of its eight analog output channels, a dedicated 12-bit digital-to-analog converter is provided that provides voltage output update rates of up to 1 MS/ SEC. The model also features eight digital input/output lines compatible with 5 V TTL/CMOS. It has 3 DMA channels with the scather-gather DMA mode, a 5V PCI master-slave bus interface.

The number of counters/timers included in the device is 2, the resolution is 24 bits, and the frequency is 20 MHz, 100 kHz. It has a frequency panzer and a basic clock of 10 MHz and 100 kHz. The maximum operating voltage of the device is ±11V, and CAT 1 is used for channel to ground isolation. ±22 V, CAT 1 is used between channels. PCI 6713 National Instruments also supports hardware-based digital triggering. This model is equipped with a DAQ-STC with a choice of logic levels, PFI lines, and frequency shift keying. In addition, the DAQ-STC brings various buffering operations such as above/below control, equivalent time sampling, monopulse generation, pulse train generation, buffering period and half-period measurement. The NI device is equipped with a 68-pin male SCSI-II I/ O connector.

PCI-6713 is a high speed analog output device.

PCI-6713 has the following features:

Provides simultaneous multi-channel updates for control and waveform output applications such as excitation response, power control, high-speed, deterministic control, and sensor/signal simulation.

Provides 8 5V TTL/CMOS digital I/O lines.

Two 24-bit 20MHz counters/timers are available.

Provides digital trigger and external clock functions.

Several instruments can be replaced, including independent proportional integral differential (PID) controllers, low-speed arbitrary waveform generators, and function generators.