PCI-6031E  数据采集卡  具有集成的过压保护功能

PCI-6031E是多功能数据采集卡。

PCI-6031E数据采集卡具有16路模拟输入、16路数字I/O、8路计数器多功能，采样频率为250kHz/通道，输入范围可编程，同时具有FIFO缓冲、硬件滤波、仪器触发、DMA传输等功能。

PCI-6031E数据采集卡广泛适用于各种数据采集应用，如机器视觉、机器人、工业自动化和科学仪器等。

PCI-6031 多功能I/O设备，PCI，64路AI（16位，100 kS/s），2路AO，8路DIO，多功能I/O设备—PCI-6031提供了模拟I/O、数字I/O和两个24位计数器/定时器。该设备为从实验室自动化、研究、设计验证/测试到制造测试等各种应用提供了经济实惠的可靠数据采集。SCC或SCXI信号调理模块可用于为设备添加传感器和高电压测量功能。随附的NI-DAQmx驱动程序和配置实用程序可简化配置和测量。

National Instruments PCI-6031E（部件号：777514-01）是一款64路单端或32路差分模拟输入通道，16位多功能DAQ。它具有两个 16 位模拟输出通道，最大更新速率为每秒 100 kS，FIFO 缓冲区大小为 2,048 个样本。该器件支持直流输入耦合，并具有集成的过压保护功能。 NI PCI-6031E 具有 3 个 DMA 通道， 支持 直接 内存 存取、 编 程 I/ O 和 中断 模式 的 数据传输。使用此型号，用户可以在 16 位分辨率下实现最大 100 kS/秒的最大采样率。该数据采集设备提供 2 个模拟输出通道，最大更新速率为每秒 100 kS，分辨率为 16 位。提供双缓冲型DAC，用于模数转换。

National Instruments PCI 6031E 具有 ±10 V、0 至 10 V 电压输出范围、0.1 Ω 最大输出阻抗、±5 mA 电流驱动，并在对地短路保护下运行。该型号支持模拟和数字触发，并配有七条RTSI触发线。在典型条件下工作时，该DAQ设备消耗1.5 A的电流。该型号支持主从型总线接口，并具有 100 针母头 0.050 D 型 I/O 连接器。NI PCI 6031E 重约 7.4 盎司，物理尺寸为 17.5 厘米× 10.6 厘米。NI 设备 的 建议 预热 时间为 15 分钟， 应 至少 每年 校准 一次。

PCI-6031E  数据采集卡  具有集成的过压保护功能

PCI-6031E is a multi-function data acquisition card.

PCI-6031E data acquisition card has 16 analog input, 16 digital I/O, 8 counter multi-function, sampling frequency is 250kHz/ channel, input range is programmable, and has FIFO buffering, hardware filtering, instrument trigger, DMA transmission and other functions.

The PCI-6031E data acquisition card is widely used in a variety of data acquisition applications, such as machine vision, robotics, industrial automation and scientific instruments.

Pci-6031 Multi-function I/O device, PCI, 64-way AI (16-bit, 100 kS/s), 2-way AO, 8-way DIO, Multi-function I/O device - PCI-6031 offers analog I/O, digital I/O, and two 24-bit counters/timers. The device provides affordable and reliable data acquisition for a variety of applications ranging from laboratory automation, research, design validation/testing to manufacturing testing. SCC or SCXI signal conditioning modules can be used to add sensors and high voltage measurement capabilities to the device. The included NI-DAQmx driver and configuration utility simplify configuration and measurement.

The National Instruments PCI-6031E (Part number: 777514-01) is a 64-channel single-ended or 32-channel differential analog input channel with 16-bit multi-function DAQ. It features two 16-bit analog output channels with a maximum update rate of 100 kS per second and a FIFO buffer size of 2,048 samples. The device supports DC input coupling and has integrated overvoltage protection. The NI PCI-6031E has three DMA channels that support direct memory access, programmed I/ O, and interrupt mode data transfer. With this model, users can achieve a maximum sampling rate of up to 100 kS/ s at 16-bit resolution. The data acquisition device offers 2 analog output channels with a maximum update rate of 100 kS per second and a resolution of 16 bits. Dual buffered Dacs are available for analog-to-digital conversion.

The National Instruments PCI 6031E has a ±10 V voltage output range of 0 to 10 V, a maximum output impedance of 0.1 Ω, a ±5 mA current drive, and operates under short-circuit protection to ground. This model supports analog and digital triggering and comes with seven RTSI trigger wires. When operating under typical conditions, the DAQ device consumes 1.5 A of current. This model supports master-slave bus interfaces and has a 100-pin female 0.050D type I/O connector. The NI PCI 6031E weighs about 7.4 ounces and has a physical dimension of 17.5 cm x 10.6 cm. The recommended warm-up time for NI equipment is 15 minutes and should be calibrated at least once a year.