MTL831B MTL 可编程逻辑 FPGA器件

MTL831B是一个集成了可编程逻辑和数字信号处理(DSP)功能的FPGA器件，具有高速并行处理能力，适用于各种数字信号处理应用。它具有以下特点：

高速并行处理能力：MTL831B采用并行架构，可以同时处理多个数据流，适用于需要高速处理的数字信号处理应用。

可编程逻辑和DSP功能：MTL831B集成了可编程逻辑和数字信号处理功能，可以灵活地实现各种数字信号处理算法和逻辑控制功能。

高性能存储器：MTL831B内置了高性能的存储器，可以存储大量的数据和处理结果，适用于需要大量数据存储和处理的应用。

高速接口：MTL831B具有高速接口，可以与其他设备进行高速数据传输和控制，适用于需要高速数据传输和控制的应用。

总的来说，MTL831B是一种高性能、灵活、高速的FPGA器件，适用于各种数字信号处理应用，如通信、图像处理、音频处理等。

:1个MTL838B-MBF(接收器)可带1或2个MTL831B(发送器)，配1或2个MTL3052(隔离栅);

多路转换系。

MTL的多路转换系统通过发送和接收单个或双冗余线对的输入和输出信号,减少了铺设危险区电缆的费用。

MTL多路转换器的选用

MTL800系列本安多路转换器系统，只通过2根导线，将危险区的多路信号传送至安全区。MTL831B多路发送器通常装在危险场合,它与现场的传感

器或开关相连，通过单根—对数据链路将这些输入信号状态传至安全区域，数据链路支持危险区和安全区之间的通讯，用MTL自己的通讯协议，当

然也向变送器提供电源，不需要现场供电。

MTL831B的典型用法是装在ENC83机箱内近量靠近现场仪表。MTL831B模拟量输入发送器

最多可监视16个处于危险场合中的热电偶或毫伏源(最大正负60mV)或15个2，3,4线制热电阻。

1.本质安全,适用0区

⒉通讯和电源从—对数据链路上经过3.同数据链路供电

4.热电偶和热电阻可在同-发送器上使用两个MTL831B多路发送器可共享同—根单对数据链路到安全区的——个隔离器或接收器或它们的组合,提供

最多32个多路转换输入。

MTL831B MTL 可编程逻辑 FPGA器件

The MTL831B is an FPGA device that integrates programmable logic and digital signal processing (DSP) capabilities with high-speed parallel processing capabilities for a variety of digital signal processing applications. It has the following characteristics:

High-speed parallel processing capability: The MTL831B uses a parallel architecture to process multiple data streams simultaneously, making it suitable for digital signal processing applications that require high-speed processing.

Programmable logic and DSP functions: The MTL831B integrates programmable logic and digital signal processing functions, which can flexibly implement various digital signal processing algorithms and logic control functions.

High-performance memory: The MTL831B has a built-in high-performance memory that can store a large amount of data and processing results, and is suitable for applications that require a large amount of data storage and processing.

High-speed interface: The MTL831B has a high-speed interface for high-speed data transmission and control with other devices, and is suitable for applications that require high-speed data transmission and control.

Overall, the MTL831B is a high-performance, flexible, high-speed FPGA device suitable for a variety of digital signal processing applications, such as communications, image processing, audio processing, etc.

:1 MTL838B-MBF(receiver) with 1 or 2 MTL831B(transmitter), with 1 or 2 MTL3052(isolation gate);

Multiplexing system.

MTL's multiplexing system reduces the cost of laying hazardous area cables by sending and receiving input and output signals from single or double redundant pairs of lines.

MTL multiplexer selection

The MTL800 series of intrinsic multiplex converter system transmits the multiplex signal from the dangerous area to the safe area through only two wires. The MTL831B multiplex transmitter is usually installed in hazardous situations where it is associated with field sensing

The device or switch is connected to transmit these input signal states to the safe zone via a single - pair data link that supports communication between the danger zone and the safe zone, using MTL's own communication protocol, when

However, it also provides power to the transmitter and does not require on-site power supply.

A typical use of the MTL831B is in an ENC83 enclosure close to the field instrument. MTL831B analog input transmitter

Monitor up to 16 thermocouples or millivolt sources at risk (up to plus or minus 60mV) or 15 2,3,4 wire heating resistors.

1. Intrinsically safe, applicable to zone 0

⒉ Communication and power supply from the opposite data link through 3. Power supply from the same data link

4. Thermocouples and thermal resistors can be used on the same transmitter. Two MTL831B multiplex transmitters can share the same single pair data link to the safe zone

Up to 32 multiplexing inputs.