MTL-8715-CA-BI MTL 模拟信号隔离总线接口模块

MTL8715-CA-BI是一款模拟信号隔离栅，主要用于隔离和传输4-20mA的模拟信号MTL 8715-CA-BI的基本参数:

输入信号:4-20mA DC

输出信号:4-20mA DC或1-5V DC隔离电压:1500V AC

频率响应范围:DC - 10kHz线性度误差:+0.1%

供电电压:18-32V DC

工作温度范围:-20°℃到+60°℃安装方式: 35mm DIN导轨安装尺寸:22.5mm x 99mm x 114mm重量:约160g

MTL 8715-CA-Bl的功能和实际运行操作:

信号隔离:MTL8715-CA-Bl可以将输入信号隔离，防止输入回路与输出回路之间的干扰，确保传输的信号质量。

信号转换:MTL8715-CA-Bl可以将4-20mA的模拟信号转换成相应的电压信号，便于各种仪表、传感器等设备的接收和处理。信号放大: MTL8715-CA-BI可以放大输入信号的幅值，使信号能够适应更远距离的传输。

信号保护:MTL8715-CA-Bl在输入和输出之间设置了隔离和保护电路，可以保护输出设备免受输入电路中的过电压、过电流等因素的影响。提高系统可靠性:MTL8715-CA-BIl的信号隔离和保护作用可以提高系统的可靠性，降低系统故障率，延长设备使用寿命。

MTL 8715-CA-BI总线接口模块底座热交换CI854A支持热交换。它可以在线更换，不会对连接到CEX总线的其他单元造成任何干扰。在热移除和随后的插入之后，该单元将自动配置。在冗余配置中，可以在不干扰主单元的情况下更换备用单元。这包括如果设备出现故障，可以在线更换。为了支持热交换，不需要配置。运行中的热配置(HCIR)在运行中进行热配置时，可以在线配置从属设备，而无需初始化PROFIBUS通热交换CI854A支持热交换。它可以在线更换，不会对连接到CEX总线的其他单元造成任何千扰。在热移除和随后的插入之后，该单元将自动配置。在冗余配置中，可以在不干扰主单元的情况下更换备用单元。这包括如果设备出现故障，可以在线更换。为了支持热交换，不需要配置。

主营产品，货源充足，全品牌DCS、PLC备件

1. lnvensys Foxboro:V/A系列系统、FBM(现场输入/输出模块）顺序控制、梯形逻辑控制、事故召回处理、DAC、输入/输出信号处理、数据通信与处理。

2.Invensys Triconex:冗余容错控制系统，现代的基于三重模块冗余(TMR)结构的容错控制器。3.西屋(Westinghouse) : OVATION系统、WDPF系统、MAX1000系统备件。

4.RockwellAllen-Bradley: ICS TRIPLEX、Reliance Ryan、SLC 500/1747/1746、MicroLogix/1761/1763/1762/1766/1764,CompactLogix/1769/1768、Logix 5000/1756/1789/1794/1760/1788, PLC-5/1771/1785等

5. Modicon: Quantum 140系列处理器、控制卡、电源模块等。

6.ABB:工业机器人备件DSQC系列(2号、3号、4号、S4C、S4C、IRC5号)，7.贝利INFI 90等

8.西门子(SIEMENS) : Siemens MOORE、西门子Simatic C1、西门子数控系统等。9.Motorola(摩托罗拉):MVME 162、MVME 167、MVME1772、MVME177等系列。10.xYCOM: v/o.VME板和处理器。

11.GE FANUC (GE FANUC):模块、卡、驱动器等备件。

12.Yaskawa (ochuan):何服控制器、何服电机、何服驱动器。

13.博世力士乐(BOSCH Rexroth) : lndramat、I/O模块、PLC控制器、驱动模块等。

14.伍德沃德(Woodward): SPC阀位控制器，PEAK150数字控制器。

15.本特利(BENTLY) : 3500检测系统全系列。

16.工业机器人系统备件。

MTL-8715-CA-BI MTL 模拟信号隔离总线接口模块

MTL8715-CA-BI is an analog signal isolation gate, mainly used to isolate and transmit 4-20mA analog signals MTL8715-CA-BI basic parameters:

Input signal :4-20mA DC

Output signal :4-20mA DC or 1-5V DC Isolation voltage :1500V AC

Frequency response range: DC-10kHz Linearity error :+0.1%

Power supply voltage :18-32V DC

Operating temperature range :-20° C to +60° C Mounting method: 35mm DIN rail Mounting dimension :22.5mm x 99mm x 114mm Weight: about 160g

Functions and actual operation of MTL 8715-CA-Bl:

Signal isolation: The MTL8715-CA-Bl can isolate the input signal, prevent interference between the input loop and the output loop, and ensure the quality of the transmitted signal.

Signal conversion :MTL8715-CA-Bl can convert 4-20mA analog signals into corresponding voltage signals, which is convenient for receiving and processing of various instruments, sensors and other equipment. Signal amplification: The MTL8715-CA-BI can amplify the amplitude of the input signal so that the signal can be adapted for longer distance transmission.

Signal protection: The MTL8715-CA-Bl provides isolation and protection circuits between input and output, which can protect the output device from overvoltage, overcurrent and other factors in the input circuit. Improve system reliability: The signal isolation and protection of the MTL8715-CA-BIl can improve system reliability, reduce system failure rates, and extend equipment service life.

MTL 8715-CA-BI bus interface module Base Heat exchange The CI854A supports heat exchange. It can be replaced online without causing any interference to other units connected to the CEX bus. After hot removal and subsequent insertion, the unit is automatically configured. In a redundant configuration, backup units can be replaced without disturbing the primary unit. This includes being able to replace the device online if it fails. To support heat exchange, no configuration is required. Hot Configuration in Operation (HCIR) During hot configuration in operation, slave devices can be configured online without the need to initialize the PROFIBUS Hot switching CI854A supports hot switching. It can be replaced online without causing any disturbance to other units connected to the CEX bus. After hot removal and subsequent insertion, the unit is automatically configured. In a redundant configuration, backup units can be replaced without disturbing the primary unit. This includes being able to replace the device online if it fails. To support heat exchange, no configuration is required.

Main products, sufficient supply, full brand DCS, PLC spare parts

1. lnvensys Foxboro:V/A series system, FBM(field input/output module) sequence control, ladder logic control, accident recall processing, DAC, input/output signal processing, data communication and processing.

2.Invensys Triconex: Redundant fault-tolerant control system, modern fault-tolerant controller based on Triple module redundancy (TMR) structure. 3. Westinghouse: OVATION system, WDPF system, MAX1000 system spare parts.

4.RockwellAllen-Bradley:  ICS TRIPLEX, Reliance, Ryan, 500/1747/1746 SLC, MicroLogix / / 1764/1762/1766, 1761/1763, Logix CompactLogix / 1769/1768 PLC / 1789/1794/1760/1788, 5000/1756-5/1771/1785, etc

5. Modicon: Quantum 140 series processor, control card, power module, etc.

6.ABB: Industrial robot spare parts DSQC series (No. 2, 3, 4, S4C, S4C, IRC5), 7. Bailey INFI 90, etc

8. SIEMENS: Siemens MOORE, Siemens Simatic C1, Siemens Numerical Control Systems, etc. 9.Motorola :MVME 162, MVME 167, MVME1772, MVME177 and other series. 10.xYCOM: v/ O.ME board and processor.

11.GE FANUC (GE FANUC): Spare parts such as modules, cards, and drivers. 

12.Yaskawa (ochuan): how to suit controller, how to suit motor, how to suit drive.

13. BOSCH Rexroth: lndramat, I/O module, PLC controller, drive module, etc.

14. Woodward: SPC valve position controller, PEAK150 digital controller. 

15. BENTLY: A complete series of 3500 inspection systems. 

16. Industrial robot system spare parts.