MVME712/M  |  处理器模块  |   MVME162-533A |   MVME162-10

型号：MVME712/M

类别：处理器模块

工作电压: 24V

功耗 :3W

配置：

• 4 个 25 针多协议 EIA-232-D 串行端口（通过 P2 适配器）

• 1 个独立打印机端口（通过 P2 适配器）

• SCSI 屏蔽连接器总线接口（通过 P2 适配器），用于连接内部和外部设备

• 前面板

特征：

4 个 25 引脚多协议 EIA-232-D 串行端口

该MVME712M是摩托罗拉 MPU VME 模块、VME 处理器模块、嵌入式控制器和单板计算机 （SBC） 系列处理器模块的 I/O 转换模块。MVME712M兼容 MVME147、MVME1600、MVME162、MVME2600、MVME167、MVME2700、MVME177、MVME3600 MVME4600。MVME712M用作处理器模块与其外围设备之间的接口。该模块的目的是提供后面板行业标准连接器，以简化外部客户的电缆要求。

P2 适配器组件将 I/O 信号和接地从机箱背板上的 P2 连接器（在 VMEmodule MPU 连接处）路由到MVME712M。该MVME712M将信号路由到四个串行端口，其前面板上有四个行业标准 DB-25 连接器。串行端口可以通过MVME 712M上的跳线布置配置为EIA-232-D DTE或DCE。MVME712M前面板还具有以太网端口、SCSI 端口和打印机端口。此外，MVME712M将 EIA-232-D 端口 2 信号路由到内部调制解调器。

MVME712/M需要使用 P2 适配器板，该板不包括在内。P2 适配器板的功能包括：

• 允许 SCSI 电缆连接到其他 SCSI 设备和/或通过扁平带状电缆

MVME712/M的连接器 • 安装在插座中的 SCSI 端接电阻器，用于电缆末端或电缆配置

的中间 • 在 P2 适配器上从连接器 P2 上的 +5 伏直流电开发的端接器电源， 和 P2 适配器上的熔断器 （1 A）

• 将 EIA-232-D 端口、打印机端口、SCSI 和以太网信号连接到MVME712M的连接器

Model: MVME712/M

Category: Memory module

Working voltage: 24V

Power consumption :3W

Settings:

• Four 25-pin multi-protocol EIA-232-D serial ports (via P2 adapter)

• 1 independent printer port (via P2 adapter)

• SCSI Shielding Connector bus interface (via P2 adapter) for connecting internal and external devices

• Front panel

Features:

Four 25-pin multi-protocol EIA-232-D serial ports

The MVME712M is an I/O conversion module for the MOTOROLA MPU VME module, VME processor module, Embedded controller, and Single Board Computer (SBC) family of processor modules. The MVME712M is compatible with MVME147, MVME1600, MVME162, MVME2600, MVME167, MVME2700, MVME177, MVME3600 and MVME4600. The MVME712M serves as the interface between the processor module and its peripherals. The purpose of this module is to provide industry standard connectors for the rear panel to simplify the cable requirements of external customers.

The P2 adapter assembly routes the I/O signal and ground from the P2 connector on the chassis backplane (at the VMEmodule MPU connection) to the MVME712M. The MVME712M routes signals to four serial ports and has four industry-standard DB-25 connectors on its front panel. The serial port can be configured as EIA-232-D DTE or DCE via the jumper arrangement on the MVME 712M. The MVME712M front panel also has Ethernet ports, SCSI ports, and printer ports. In addition, the MVME712M routes the EIA-232-D port 2 signal to the internal modem.

The MVME712/M requires the use of a P2 adapter board, which is not included. The functions of P2 adapter board include:

Allows SCSI cables to be connected to other SCSI devices and/or via flat ribbon cables

Connectors for the MVME712/M • SCSI terminating resistors mounted in receptacles for cable ends or cable configurations

• Terminal power supply developed on P2 adapter from +5 volts DC on connector P2, and fuse (1 A) on P2 adapter

• Connect the EIA-232-D port, printer port, SCSI and Ethernet signals to the connector of the MVME712M