IS200EISBH1AAC  电路板  用于访问复位开关

产品描述

IS2OOEISBH1AAC是GE Mark VIl电路板。该板通常在EX2100激励模块中用作激励器ISbus板。该委员会负责管理其机柜内的光纤通信。

该IS2OOESBH1AAC内置一个前面板，该面板包括两个固定销，一旦将板安装在机架系统中，即可将板锁定到位。这些标有主板ID号和通用电气标志。在这两老

之=间，电路板有一个开口，用于访问复位开关(实际上位于电路板表面)和几个光纤连接器。光纤连接器标记为Gen Field voltage and current、Exciter voltage

and current以及Ground Detect In and Out。面板使用螺钉连接到电路板。

电路板上标有多个代码和条形码。它在几个位置沿其边缘进行工厂钻孔。该板还标有GE标志。

组件标有参考指示符。该板有二十多个集成电路。它具有电感线圈、电阻器、电容器、多个晶体管和二极管，以及上述复位开关。该板还具有两个小型变压器和一个背板连接器，用于光纤反馈信号的输入和输出。

有关S20QESBH1AAC电路板的更多信息，请参阅通用电气的出版物，如原始手册或数据表。如果您不再提供这些产品，AXControl可能会随您的订单一起为您提供更换产品。

lS200EISBH1A GE励磁机ISBus板专用的通信接口板

IS200EISBH1A励磁机ISBus板是—种专用的通信接口板，用于在励磁机的M1、M2和C控制器之间传输数据。它是—种3U高的模块，位于DSPX下方的控制机架中，通过前面板上的光纤连接器接收来自发电机磁场(必要时还包括励磁机)的电流和电压信号，并将信号接收和传输到接地检测模块。

IS200EISBH1AAC  电路板  用于访问复位开关

Product description

IS2OOEISBH1AAC is a GE Mark VIl circuit board. This board is commonly used as an exciter ISbus board in EX2100 excitation modules. The committee is responsible for managing fiber optic communications within its cabinets.

The IS2OOESBH1AC has a built-in front panel that includes two retaining pins that lock the board into place once it is installed in the rack system. These are marked with the motherboard ID number and the GE logo. In these two old

the

The board has an opening for access to the reset switch (which is actually located on the surface of the board) and several fiber optic connectors. The optical fiber connectors are marked with Gen Field voltage and current, and Exciter voltage

and

current as well as Ground detection In and Out. The panel is attached to the circuit board using screws.

The circuit board is marked with multiple codes and barcodes. It drilled factory holes at several locations along its edge. The board is also marked with the GE logo.

Components are marked with reference indicators. The board has more than twenty integrated circuits. It has an inductor coil, a resistor, a capacitor, multiple transistors and diodes, and the said reset switch. The board also has two small transformers and a backplane connector for the input and output of the fiber feedback signal.

For more information about S20QESBH1AAC boards, please refer to GE publications such as original manuals or data sheets. If you no longer supply these products, AXControl may provide you with a replacement product along with your order.

lS200EISBH1A Communication interface board dedicated to the ISBus board of the GE exciter

The IS200EISBH1A exciter ISBus is a dedicated communication interface board used to transmit data between the M1, M2, and C controllers of the exciter. It is a 3U high module, located in the control rack below the DSPX, receives the current and voltage signals from the generator's magnetic field (including the exciter if necessary) through the fiber optic connector on the front panel, and receives and transmits the signals to the grounding detection module.