531X302DCIAWG1  直流电源  用于在驱动器、励磁机

品牌:GE

·型号:531x302DCIAWG1

产品规格

·工作电压:100-240VAC

无识别结果

·最大负载电流:25A

。尺寸:100mm x 50mm x 30mm应用领域

·工业自动化控制系统·电力系统

产品使用说明

请参考附带的产品手册和安装指南进行安装和使用。产品介绍

GE 5313302DCIAWG1是一款高性能的直流电源，可满足工业自动化控制系统和电力系统的要求。它具有高效率、稳定性和可靠性等优点。

531X307LTBAFG1可用作局域网端子板。它通常安装在传动或励磁机柜内。端子板用于在驱动器、励磁机或其他控制设备和连接的外部设备如联锁装置、按钮、接触器或指示灯之间创建接口。

该板有两个版本。G1LTB内置8个24VDC输入插头，相比之下，G2LTB板没有这些输入，而是使用来自连接器端子的直流输入信号。

531X307LTBAFG1设计有三个端子板，位于一条长边上。沿着相对的边缘，电路板有两个垂直引脚连接器，以及前面提到的输入插头。电路板上还有一长串LED指示灯，横跨电路板的整个长度。总共有15个LED指示灯。其它电路板元件包括晶体管、七个继电器、多个金属氧化物变阻器，以及电阻、二极管和电容。该板标有GE标志和板ID号，并且在其中心附近带有条形码。此外，单个部件标有参考名称。

请务必注意，任何主板更换都应该从关闭主板电源开始。这是为了防止任何触电的机会，以及防止可能对驱动器或其他设备造成的损坏。

531X302DCIAWG1  直流电源  用于在驱动器、励磁机

Brand :GE

· Model :531x302DCIAWG1

Product specification

· Working voltage :100-240VAC

No recognition result

· Maximum load current :25A

. Size :100mm x 50mm x 30mm Application area

· Industrial automation control system · Power system

Product instructions

Please refer to the attached product manual and installation guide for installation and use. Product introduction

The GE 5313302DCIAWG1 is a high-performance DC power supply that meets the requirements of industrial automation control systems and power systems. It has the advantages of high efficiency, stability and reliability.

The 531X307LTBAFG1 can be used as a LAN terminal board. It is usually installed in a drive or excitation cabinet. The terminal board is used to create an interface between a driver, exciter, or other control device, and connected external devices such as interlocks, buttons, contactors, or indicators.

There are two versions of the board. The G1LTB has eight built-in 24VDC input plugs, in contrast, the G2LTB board does not have these inputs, but instead uses a DC input signal from the connector terminals.

The 531X307LTBAFG1 design has three terminal boards located on one long side. Along opposite edges, the board has two vertical pin connectors, as well as the input plugs mentioned earlier. The board also has a long string of LED indicators that span the entire length of the board. There are 15 LED indicators in total. Other board components include transistors, seven relays, multiple metal oxide rheostat, as well as resistors, diodes, and capacitors. The board is marked with the GE logo and board ID number, and has a barcode near its center. In addition, individual parts are labeled with reference names.

It is important to note that any motherboard replacement should start with the motherboard being powered off. This is to prevent any chance of electric shock, as well as to prevent possible damage to the drive or other equipment.