DS200RTBAG3AEB GE  励磁板 连接通过信号控制继电器

DS200RTBAG3AEB是通用电气驱动系统中的一种可选板。

DS200RTBAG3AEB具有10个继电器，可直接从绘图继电器驱动或由用户远程驱动，52个端子点，可用于连接通过信号控制继电器和驱动器行为的电线。如果需要验证继电器设置是否正确，或者怀疑驱动器或DS200RTBAG3AEB板有问题，可以在设备断电的情况下，使用万用表测量端子板上公共电源与各个端子之间的电压，正常电压在0~1V之间变化，如果测量的电压正常，则说明继电器没有问题；如果测量的电压为0V，则说明该端子与公共电源没有连接，可能是断线或接触不良。

GE励磁板DS200RTBAG3AEB是安装在驱动柜中的可选板，它具有十个继电器，这些继电器可以直接从绘图继电器驱动，也可以由用户远程驱动。 该DS200RTBAG3AEB包含 52 个接线点，可用于连接控制继电器行为和驱动器通过信号的电线。

如果您需要验证继电器是否正确设置，或者您怀疑驱动器或DS200RTBAG3AEB板有问题，则可以在驱动器上进行诊断。您可以从控制面板访问诊断程序。通过键盘上的键，您可以访问诊断程序。诊断程序提供有关驱动器和所有主板的包容性报告。您可能会发现将报告下载到笔记本电脑上更容易，您可以在其中保存报告、将其打印在纸上或搜索报告。

确定必须更换主板后，在断开所有电源之前，请勿触摸驱动器中的主板或驱动器中的任何组件。高压电流在驱动器中，断开电源后，必须等待 5 秒钟，让电流离开组件。测试电路板和其他组件是否存在电流。在确定电流已退出之前，不要触摸任何东西。一些组件在电路板通电和使用时存储电流。在电路板断开后等待为电流消散提供了时间。

DS200RTBAG3AEB GE  励磁板 连接通过信号控制继电器

The DS200RTBAG3AEB is an optional board in General Electric drive systems.

The DS200RTBAG3AEB has 10 relays that can be driven directly from the drawing relay or remotely by the user, and 52 terminal points that can be used to connect wires that control the behavior of the relay and driver through signals. If you need to verify the correct setting of the relay, or suspect that there is a problem with the driver or DS200RTBAG3AEB board, you can use a multimeter to measure the voltage between the common power supply and each terminal on the terminal board when the device is powered off. The normal voltage varies between 0 and 1V. If the measured voltage is normal, it indicates that the relay is not wrong. If the measured voltage is 0V, it indicates that the terminal is not connected to the public power supply, which may be broken or poor contact.

The GE excitation board DS200RTBAG3AEB is an optional board mounted in the drive cabinet with ten relays that can be driven directly from the drawing relay or remotely by the user. The DS200RTBAG3AEB contains 52 connection points that can be used to connect wires that control relay behavior and drive through signals.

If you need to verify that the relay is set correctly, or if you suspect that there is a problem with the drive or DS200RTBAG3AEB board, you can diagnose it on the drive. You can access the diagnostics from the Control panel. With the keys on the keyboard, you can access the diagnostic program. The diagnostic program provides inclusivity reports on drives and all motherboards. You may find it easier to download the report to your laptop, where you can save it, print it on paper, or search for it.

After determining that the motherboard must be replaced, do not touch the motherboard in the drive or any components in the drive until all power is disconnected. High voltage current in the driver, after disconnecting the power supply, you must wait 5 seconds for the current to leave the component. Test circuit boards and other components for current. Do not touch anything until you are sure the current has exited. Some components store current when the board is energized and in use. Waiting after the board is disconnected provides time for the current to dissipate.