DS200DCFBG1BJB  GE 电源板 对传感器状态的监测

制造者 GE通用电气

系列 Mark V、AC2000、CB2000、DC2000、FC2000、ME2000 和 EX2000

零件编号 DS200DCFBG1B

产品类型 电源板

说明书 GEI-100028

DS200DCFBG1BJB是通用电气制造的板组件，是Mark V Speedtronic系统的一部分。

DS200DCFBG1BJB用于为驱动器和机箱风扇提供控制级电源，用于EX2000应用以及DC2000、FC2000、GF2000、ME2000、CB2000和AC2000IGBT驱动应用。是一块大型矩形电路板，其表面安装有大量元件。

DS200DCFBG1B是通用电气为Mark V板系列制造的电源板。AC2000、CB2000、DC2000、FC2000、ME2000 和 EX2000 系列机器可以将主板安装在驱动器中。安装后，此卡可以为驱动器提供控制级电源和机柜风扇电源。额定电压在 38 至 115 VAC 之间，可通过控制电源变压器直接提供给电路板。电路板的频率取决于输入电压，但范围为 0 至 500 kHz。

该板具有许多电路，用于为电路板和已安装的驱动器供电。DS200DCFBG1B由电机励磁电源、驱动器、AC/DC 监控和控制级电源电路组成。板上的 12 个跳线和 7 个 DIP 开关为用户提供了可配置的系统选项。保险丝开关诊断使用电路板上的两个 LED 和一个霓虹灯指示灯进行。三个保护保险丝可防止电源中断。可以使用电路板上集成的五个测试点来监控电压。

应遵循制造商提供的DS200DCFBG1B和已安装驱动器的安装和存储参数。 这些将防止对两个单元造成任何意外或可预防的损坏。有关接线和安装电路板的完整指南，请参阅设备的手册和数据表。最初，该板和 Mark V 系列的技术支持由制造商通用电气提供。

DS200DCFBG1BJB的作用是控制驱动器和机箱风扇的电源，以及控制热电偶传感器的输出信号。

DS200DCFBG1BJB是通用电气制造的电路板组件，作为Mark V Speedtronic系统的一部分，用于为驱动器和机箱风扇提供控制级电源。它是一个大的矩形电路板，其表面安装了大量组件，其中包括4个4位DIP开关器件和4个可配置跳线。它还可以提供对传感器状态的监测和诊断功能，以及接收和处理热电偶传感器的输出信号，将其转换为数字信号或模拟信号，并将温度数据传送到监控或控制系统中。

DS200DCFBG1BJB  GE 电源板 对传感器状态的监测

Manufacturer GE General Electric

Series Mark V, AC2000, CB2000, DC2000, FC2000, ME2000 and EX2000

Part number DS200DCFBG1B

Product Type Power supply board

Instruction Manual GEI-100028

The DS200DCFBG1BJB is a board assembly manufactured by General Electric as part of the Mark V Speedtronic system.

The DS200DCFBG1BJB is used to provide control level power for drivers and chassis fans for EX2000 applications as well as DC2000, FC2000, GF2000, ME2000, CB2000 and AC2000IGBT driver applications. It is a large rectangular circuit board with a large number of components mounted on its surface.

The DS200DCFBG1B is a power supply board manufactured by General Electric for the Mark V board series. AC2000, CB2000, DC2000, FC2000, ME2000 and EX2000 series machines can have the motherboard installed in the drive. When installed, the card provides control level power to the drive and cabinet fan power. The rated voltage is between 38 and 115 VAC and can be supplied directly to the board via a control power transformer. The frequency of the board depends on the input voltage, but ranges from 0 to 500 kHz.

The board has a number of circuits that are used to power the circuit board and the installed drivers. DS200DCFBG1B is composed of motor excitation power supply, driver, AC/DC monitoring and control level power supply circuit. The 12 jumpers and 7 DIP switches on the board provide users with configurable system options. Fuse switch diagnosis is performed using two leds and a neon indicator on the circuit board. Three protective fuses prevent power outages. The voltage can be monitored using five test points integrated on the board.

Installation and storage parameters for DS200DCFBG1B and installed drives provided by the manufacturer should be followed. These will prevent any accidental or preventable damage to both units. For complete guidance on wiring and mounting boards, refer to your device's manual and data sheet. Initially, technical support for the board and the Mark V series was provided by manufacturer General Electric.

The role of the DS200DCFBG1BJB is to control the power supply to the driver and the chassis fan, as well as to control the output signal of the thermocouple sensor.

The DS200DCFBG1BJB is a circuit board assembly manufactured by General Electric as part of the Mark V Speedtronic system to provide control-level power to drivers and chassis fans. It is a large rectangular circuit board with a large number of components mounted on its surface, including four 4-bit DIP switching devices and four configurable jumpers. It can also provide monitoring and diagnostic functions of the sensor status, as well as receiving and processing the output signal of the thermocouple sensor, converting it into a digital signal or an analog signal, and transmitting temperature data to the monitoring or control system.