IS200EISBH1AAC GE 励磁器通信板 控制器之间的数据传输

型号：IS200EISBH1AAC

品牌：GE

IS2O0OEISBH1AAC是阿格Mark Vl电路板。该板通常在EX2100励磁模块中用作励磁机ISbus板。该板负责管理其机柜内的光纤通信。

IS20OEISBH1AAC配有一个前面板，该面板包括两个定位销，一旦将板安装到机架系统中，这些定位销会将板锁定到位。这些都标有电路板id号和通用电气公司的标志。在这两者之间，板有一个开口，以访问复位开关(实际上位于板的表面和几个光纤连接器。光纤连接器标有发电机磁场电压和电流、励磁机电压和电流以及接地检测输入和输出。面板用螺钉连接到电路板上。

电路板上标有几个代码和条形码。它是工厂沿其边缘在几个位置钻孔。该板还标有通用电气公司的标志。

组件标有参考标记。该板有二十多个集成电路。它有电感线圈、电阻、电容、几个晶体管和二极管，以及前面提到的复位开关。该板还有两个小型变压器和一个背板连接器，用于光纤反馈信号的输入和输出。

IS200EISBH1AAC是一种励磁器通信板用于控制器之间传输数据

功能描述

lSBus是GE专有的通信接口，用于在励磁机的M1、M2和C控制器之间传输数据。EISB是一个单插槽、3U高的模块，位于DSPX下方的控制机架中。

●它通过前面板上的光纤连接器接收来自发电机磁场(必要时还包括励磁机)的电流和电压信号，并将信号接收和传输到接地检测模块。

IS200EISBH1AAC应用数据

EISB没有LED指示灯、跳线或保险丝。

连接器

以下光纤连接器位于电路板的前面板上，用于接收和传输变频信号:

EDCF板发电机现场直流电压输入

●直流发电机场EDCF板的电流输入

EDCF励磁器电压输入(可选)

●EDCF励磁器电流输入(可选)

●接地探测器电压输入

●接地探测器的电压输出复位开关也凹进前面板下部的孔后面。

IS200EISBH1AAC GE 励磁器通信板 控制器之间的数据传输

Model: IS200EISBH1AAC

Brand: GE

IS2O0OEISBH1AAC is an Agmark Vl circuit board. The board is commonly used as an exciter ISbus board in EX2100 exciter modules. The board is responsible for managing fiber optic communications within its cabinet.

The IS20OEISBH1AAC is equipped with a front panel that includes two dosing pins that lock the board into place once it is installed into the rack system. These are marked with the board id number and the GE logo. In between the two, the board has an opening to access the reset switch (which is actually located on the surface of the board and several fiber optic connectors. Fiber optic connectors are labeled with generator field voltage and current, exciter voltage and current, and ground detection inputs and outputs. The panel is attached to the circuit board with screws.

The circuit board is marked with several codes and barcodes. It is drilled in several locations along its edge of the plant. The board also bears the logo of the General Electric Company.

Components are marked with reference marks. The board has more than twenty integrated circuits. It has inductors, resistors, capacitors, several transistors and diodes, and the aforementioned reset switch. The board also has two small transformers and a backplane connector for the input and output of the fiber feedback signal.

The IS200EISBH1AAC is an exciter communication board used to transmit data between controllers

Function description

lSBus is GE's proprietary communication interface for transferring data between the exciter's M1, M2, and C controllers. The EISB is a single-slot, 3U high module located in the control rack under the DSPX.

It receives current and voltage signals from the generator's magnetic field (and exciter if necessary) through a fiber optic connector on the front panel, and receives and transmits the signal to the ground detection module.

IS200EISBH1AAC Application data

EISB has no LED indicators, jumpers, or fuses.

coupler

The following fiber optic connectors are located on the front panel of the board to receive and transmit frequency conversion signals:

EDCF board generator field DC voltage input

● Current input of EDCF board for DC power generation airport

EDCF exciter voltage input (optional)

●EDCF exciter current input (optional)

● Ground detector voltage input

● The voltage output reset switch of the ground detector is also recessed behind the hole in the lower part of the front panel.