IS200DTAOH1ABA-IS210DTAOH1AA GE 紧凑型输入板 蒸汽轮机管理系统

产品编号:IS200DTAIH1ABB

制造商:GE Boards & Turbine Control

商品编号SKU:IS20ODTAIH1ABBGBTC

系列: Mark VI IS200

IS20ODTAH1ABB是为Mark VI系统创建的GE组件。Mark Vl是以Speedtronic系列名称发布的燃气√/蒸汽轮机管理系统。自1960年代以来，该系列一直用于涡轮机管理的各种迭代。Mark VI具有以太网通信功能，并在硬件和软件中包括板载诊断(限制检查)。

IS20ODTAIH1ABB是单工模拟输入/输出端子板。它是一款用于模拟信号的紧凑型输入板。该板安装在塑料支架中，允许将PCB安装在DN导轨上。该板有0个模拟输入和20个模拟输出。输出为O-200mA，但可以通过重新配置跳线来配置为<>-<>mA电流。

IS20ODTAIH1ABB有一个带门锁紧固件的37针连接器。这被标记为JR1。该板有一个带有1个螺钉连接的端子板（TB48)。该端子排永久安装在电路板上。接线端子上通常使用#18 AWG电线的屏蔽双绞线。请注意，螺钉43/44被指定为接地(SCOM）连接。地线应尽可能短。该板有1个跳线开关这些标记为JP1OA/B-JP20A/B (O)加JP<>。该板还包括各种电容器、电阻器和集成电路，以及四个小型子面板。电路板上的跳线用于配置电流和电压。

该IS20ODTAIH1ABB的技术支持由GE提供。有关此PCB、其组件或安装程序的信息可通过手册、用户指南和数据表找到。

IS200DTAIH1ABB MarkVle控制系统是一个灵活的平台，适合各类应用。它具有为单重化、双重化冗余和三重化冗余系统配置的基于高速网络的输入√输出(/0)。基于以太网的/O可以方便地传输至全厂各类配套设施应用。V/O、控制器、监控界面与操作员和维护工作站及第三方系统之间采用了工业标崔以太网通信。

ControlST*软件包与Mark Vle控制系统及相关系统配合，用于编程、配置、跟踪及分析诊断。分布式控制解决方案(DCS）功能块库可加快配套设施应用程序的创建速度。运行时，该系统在控制器内和工厂层面提供高品质、时间相干的数据，以便有效地管理控制系统设备

IS200DTAOH1ABA-IS210DTAOH1AA GE 紧凑型输入板 蒸汽轮机管理系统

Product ID :IS200DTAIH1ABB

Manufacturer :GE Boards & Turbine Control

Product number SKU:IS20ODTAIH1ABBGBTC

Series: Mark VI IS200

The IS20ODTAH1ABB is a GE component created for the Mark VI system. The Mark Vl is a gas/steam turbine management system released under the Speedtronic family name. The series has been used in various iterations of turbine management since the 1960s. The Mark VI has Ethernet communication capabilities and includes onboard diagnostics (limit checks) in both hardware and software.

IS20ODTAIH1ABB is a simplex analog input/output terminal board. It is a compact input board for analog signals. The board is mounted in a plastic bracket that allows the PCB to be mounted on the DN rail. The board has 0 analog inputs and 20 analog outputs. The output is O-200mA, but can be configured to <>-<>mA current by reconfiguring the jumper.

The IS20ODTAIH1ABB has a 37-pin connector with a door lock fastener. This is labeled JR1. The board has a terminal board (TB48) with 1 screw connection. The terminal block is permanently installed on the circuit board. Shielded twisted pair of #18 AWG wire is usually used on the terminal. Note that screws 43/44 are designated for ground (SCOM) connections. Ground cables should be as short as possible. The board has 1 jumper switch and these are labeled JP1OA/B-JP20A/B (O) plus JP<>. The board also includes a variety of capacitors, resistors and integrated circuits, as well as four small sub-panels. Jumpers on the board are used to configure current and voltage.

The technical support for the IS20ODTAIH1ABB is provided by GE. Information about this PCB, its components, or installer can be found in manuals, user guides, and data sheets.

The IS200DTAIH1ABB MarkVle control system is a flexible platform for a wide range of applications. It has high-speed network-based input √ output (/0) configured for uniplex, dual redundancy and triple redundancy systems. Ethernet-based /O can be easily transmitted to various supporting facilities throughout the plant. Industrial standard Ethernet communication is used between the V/O, controller, monitoring interface and operator and maintenance workstations and third-party systems.

The ControlST* package works with the Mark Vle control System and related systems for programming, configuration, tracking, and diagnostic analysis. The Distributed Control Solution (DCS) function block library speeds up the creation of supporting facility applications. When running, the system provides high-quality, time-coherent data both within the controller and at the plant level for efficient management of control system equipment