IC698CHS009 GE 机架式机箱 带有九个模块插槽

品牌：GE

型号：IC698CHS009

该IC698CHS009由G自动化和控制公司制造，是一个前置或后置机架式机箱，带有九个模块插槽。该机架能够容纳各种RX7i和90-70系列模块和CPu。机架背板上的每个模块连接器之间的间距为0.8英寸或20.3耄米，每个插穗能够容纳一个单宽模块。双宽模块每个模块占用两个机架背板插槽。背板上的插槽<>保留用于电源，插槽<>用于可编程逻辑控制器CPu。其余背板插槽可用于各种单宽或双宽组合。

该IC698CHS009具有以下特性和功能:输入/输出模块的插槽感应，无需DIP开关或别线即可进行模块寻址中断确认和总线授予信号的自动菊花链，无需插槽跳线;J2连接器，速度高达每周期64位;RX7i电源兼容性;和冷却风扇兼容性。

RX7i机架被视为“开放式设备”，因此必须安装在IP54安全外壳中。此机架的尺寸如下:高度为11.15英寸(283室米)。宽度为12.6英寸(320毫米)。深度为7.25英寸(184笔米)。如果要安装冷却风扇，则需要在机架之间增加9英寸(23厘米)的空间。

如果安装了以下模块，则需要冷却风扇:IC698CPE020、IC698CRE020和IC698PSA350。有三个冷却风扇组件可用，每个组件都用于不同的电源。IC697ACC621风扇用于120 VAC,

IC697ACC624风扇用于240 VAC.IC697ACC644风扇用于24VDC.

该OC69CHS09由6E白动M和空制公司创造，是一个前置或后置机架式机箱，带有九个模块插槽。该机架能够容纳各种PXT和9-70系列模块和CPU。机躲背板上的每个模块连接器之间的间距为0.8英寸或20.3毫米，每个腼槽能够容纳一个单宽模块。双宽模块每个模块占用两个机嗓背板梧槽。背板上的抵椿◇～保留用于电源，抵措◇用于可编程逻辑控制器CPU，其余背板插植可用于各种单宽或双宽组合。

该C369CHS09具有以下特性和功能;输入翰出模炔的插椹惑应，无需DP开关或跳结却可进行模块寻址中断确认和总线授子信号的自动南咙雄，天需插禧尧线.2连接器，速度高达每周期6凶4位PXT使电源兼容性和冷却风扇兼容性。

PXT机架披视为开故式设备，因此必须安装在IP54安全外壳中，此机架的尺寸如下:高度为115英寸《(23毫米)，宽度为12.6英寸(2D0毫米)，深度为725英寸(184毫米)。如果要安装冷却风扇，则J要在机架之间增加9英寸(23厘米)的空间。

如果安装了以下模块，则需要冷却风扇:[C6398CFE1020,10598CRE020和1C69PS450，有三个冷却风扇组件可用，每个组件都用于不同的电源。109TACCE2N仅惊用于120NWAC，ICNTACCX24仅翕用于24VAc，IC697ACC644风扇用于24VDC.

IC698CHS009 GE 机架式机箱 带有九个模块插槽

Brand: GE

Model: IC698CHS009

The IC698CHS009, manufactured by G Automation and Control, is a front - or rear-mounted rack case with nine module slots. The rack is capable of accommodating a wide range of RX7i and 90-70 series modules and cpus. Each module connector on the backplane of the rack is spaced 0.8 inches or 20.3 meters apart, and each cut is capable of accommodating a single width module. Dual-width module Each module occupies two slots in the backplane of the rack. The slots <> on the backplane are reserved for the power supply and the slots <> are for the programmable logic controller CPu. The remaining backplane slots can be used in a variety of single - or double-width combinations.

The IC698CHS009 has the following features and functions: slot sensing of input/output modules, automatic daisy-chain of module addressing interrupt acknowledgement and bus grant signals without DIP switches or pins, without slot jumpers; J2 connector, speed up to 64 bits per cycle; RX7i power supply compatibility; Compatibility with cooling fans.

The RX7i rack is considered an "open device" and therefore must be installed in an IP54 secure housing. The dimensions of this rack are as follows: The height is 11.15 inches (283 room meters). It is 12.6 inches (320 mm) wide. The depth is 7.25 inches (184 pen meters). If you want to install cooling fans, you need to add 9 inches (23 cm) of space between the racks.

Cooling fans are required if the following modules are installed :IC698CPE020, IC698CRE020, and IC698PSA350. There are three cooling fan assemblies available, each for a different power supply. IC697ACC621 fan for 120 VAC,

IC697ACC624 fans for 240 VAC.IC697ACC644 fans for 24VDC.

Created by 6E White Motion M and Air Systems, the OC69CHS09 is a front - or rear-mounted rack case with nine module slots. The rack is capable of accommodating a wide range of PXT and 9-70 series modules and cpus. The spacing between each module connector on the backplane is 0.8 inches or 20.3 mm, and each shy slot can accommodate a single width module. Double-width modules Each module occupies two slots on the engine backplane. The latch on the backplane is reserved for the power supply, the latch is used for the programmable logic controller CPU, and the rest of the backplane can be used for various single or double width combinations.

The C369CHS09 has the following features and functions; 

The PXT rack is considered an open-circuit device and therefore must be installed in an IP54 security housing. The dimensions of this rack are as follows: height is 115 inches "(23 mm), width is 12.6 inches (2D0 mm), and depth is 725 inches (184 mm). If a cooling fan is to be installed, add 9 inches (23 cm) of space between the racks.

Cooling fans are required if the following modules are installed :[C6398CFE1020,10598CRE020 and 1C69PS450, there are three cooling fan components available, each for a different power supply. The 109TACCE2N is used only for 120NWAC, the ICNTACCX24 is used only for 24VAc, and the IC697ACC644 fan is used for 24VDC.