IC694ALG220 GE 模拟输入组件 中央处理器

品牌：GE

型号：IC694ALG220

零件号码

IC694ALG220

产品类型:模拟输入组件

IC695CPU315是GE Fanuc PACSystems RX3i系列的一款1 GHz中央处理器，它有一个英特尔赛扬-M微处理器，带有20 MB用户内存和20 MB闪存1

它配备了RS-232串行端口和嵌入式以太网接口，以及5 MB RAM（用户内存）和5 MB非易失性闪存存储器。控制器模块支持多达512个程序块，每个程序块可达128 KB。使用Proficy Machine Edition软件通过以太网配置IC695CPU3152。

这个处理器的优点有：

中央处理器有一个英特尔赛扬-M微处理器。

带有20 MB用户内存和20 MB闪存。

配备了RS-232串行端口和嵌入式以太网接口。

支持多达512个程序块，每个程序块可达128 KB。

这个处理器的缺点有：

价格高。

不支持热插拔。

该模以输入模块不支持热插拔，这意味着它不能安装在仍然通电并连接到电源的系统中或从该系统中移除。尝试热插拔lC694ALG220模拟输入模块可能会导致设备损坏或严重伤害。该输入模块有4个输入通道。在5伏DC电压下，该模块具有27毫安和0.135瓦的最大负载要求。它可以接受-10到+10伏范围内的输入电压。该模块上的4个输入通道中的每一个都可以处理4至20毫安的输入电流，并在所有输入端子之间进行跳线。

GE Fanuc RX3i PAC system IlC 694 alg 220模拟输入模块可安装在阿格RX3iPLC系统的任何可用/O插槽中。其每个输入通道的转换速度为1毫秒，每个通道的更新速率为4室秒。当C694ALG220模拟输入模块安装在阿格RX3通用背板中时，它需要一个额定24伏DC的外部电源，并通过左侧的TB1连接器连接到背板。当IC694ALG220模拟输入模块安装在RX3远程或扩展背板中时，它由背板电源以24伏DC隔离输出电压供电。

IC694ALG220 GE 模拟输入组件 中央处理器

Brand: GE

Model: IC694ALG220

Part number

IC694ALG220

Product Type: Analog input components

The IC695CPU315 is a 1 GHz CPU from the GE Fanuc PACSystems RX3i family that has an Intel Celeron-M microprocessor with 20 MB of user memory and 20 MB of flash 1

It is equipped with an RS-232 serial port and an embedded Ethernet interface, as well as 5 MB RAM (user memory) and 5 MB non-volatile flash memory. The controller module supports up to 512 blocks of 128 KB each. Configure the IC695CPU3152 over Ethernet using Proficy Machine Edition.

The advantages of this processor are:

The central processing unit has an Intel Celeron-M microprocessor.

Comes with 20 MB of user memory and 20 MB of flash memory.

Equipped with RS-232 serial port and embedded Ethernet interface.

Supports up to 512 blocks of 128 KB each.

The disadvantages of this processor are:

The price is high.

It does not support hot swap.

The module is not hot-swappable, which means it cannot be installed in or removed from a system that is still powered on and connected to a power supply. Hot swap the lC694ALG220 analog input module may cause device damage or serious injury. The input module has four input channels. At 5 volts DC, the module has a maximum load requirement of 27 MA and 0.135 watts. It can accept input voltages in the range -10 to +10 volts. Each of the four input channels on the module can handle input currents from 4 to 20 mA and make jumpers between all input terminals.

The GE Fanuc RX3i PAC system IlC 694 alg 220 analog input module can be installed in any available /O slot of the AG RX3iPLC system. It has a conversion rate of 1 millisecond per input channel and an update rate of 4 compartment seconds per channel. When the C694ALG220 analog input module is installed in an Arger RX3 universal backplane, it requires an external power supply rated at 24 volts DC and is connected to the backplane via the TB1 connector on the left. When the IC694ALG220 analog input module is installed in the RX3 remote or expansion backplane, it is powered by the backplane power supply at 24 volts DC isolated output voltage.