GE-8102-HO-IP GE 模拟输出计数 光学传感器

品牌:GE

型号:8102-HO-IP

原产地︰美国

零件号码

8102-HO-IP

模拟输出计数和类型

8点单端4-20ma;非易燃场电路分辨率和速度

12位;20mS0.75秒HART

产品参数

传感器类型:光学传感器

分辨率:1200 dpi

扫描速度:25 ppm

最大扫描面积:216x 356 mm

连接方式:USB2.0

特性

PAC8000I/0是一种完全模块化的/O解决方案，适用于一般用途和危险区域应用。它提供了各种各样的/O功能，并具有一个开放的架构，允许通过选择适当类型的总线接口模块(BIM)或控制器与各种不同的现场总线通信。

现场终端(每个/O模块一个)连接到载体上，无需额外的终端或连接即可接受现场布线。如果在野外损坏，可以很容易地更换。全面的机械键控系统确保设备安全。

载体通过安装在平板或T型或g型DIN导轨上形成pac8O0的物理和电气骨干。支持BIM/Controller、电源、V/O模块和现场终端的互连，承载内部Railbus的地址、数据和电源线

开路和短路检测

阀门定位器和远程指示器;

GE-8102-HO-IP 模拟输出计数是一种在模拟系统中进行计数的技术。在模拟系统中，信号是连续的模拟信号，因此计数器需要能够处理模拟信号的输入和输出。

GE-8102-HO-IP模拟输出计数器通常采用电压或电流等物理量来表示计数值。当模拟信号输入到计数器时，计数器会对其进行采样，将模拟信号转换为数字信号，并进行计数。计数值可以通过数字接口或模拟接口输出，其中数字接口通常采用串行或并行通信方式，而模拟接口则直接输出模拟信号。

GE-8102-HO-IP模拟输出计数器的优点是可以直接与模拟系统中的其他设备进行接口，无需进行数模转换。同时，它也可以提供高精度的计数值，适用于需要高精度测量和控制的应用场景。但是，由于模拟系统的复杂性和不确定性，模拟输出计数器的稳定性和可靠性可能会受到一定的影响。

需要注意的是，模拟输出计数器和数字输出计数器是不同的概念，因此在选择和使用时需要根据实际应用场景和需求进行选择。

GE-8102-HO-IP GE 模拟输出计数 光学传感器

Brand :GE

Model :8102-HO-IP

Country of Origin: USA

Part number

8102-HO-IP

Analog output counts and types

8 o 'clock single end 4-20ma; Non-flammable field circuit resolution and speed

12 bits; 20mS0.75 seconds HART

Product parameter

Sensor type: Optical sensor

Resolution :1200 dpi

Scanning speed :25 ppm

Maximum scanning area :216x 356 mm

Connection mode :USB2.0

peculiarity

The PAC8000I/0 is a fully modular /O solution for general purpose and hazardous area applications. It offers a wide variety of /O functions and has an open architecture that allows communication with a variety of different fieldbuses by selecting the appropriate type of bus interface module (BIM) or controller.

Field terminals (one per /O module) are connected to the carrier and can accept field wiring without additional terminals or connections. If damaged in the field, it can be easily replaced. A comprehensive mechanical keying system ensures equipment safety.

The carrier forms the physical and electrical backbone of pac8O0 by mounting on a flat plate or T or g DIN rail. Supports the interconnection of BIM/Controller, power supply, V/O modules, and field terminals, and carries the address, data, and power cables of the internal Railbus

Open and short circuit detection

Valve positioners and remote indicators;

GE-8102-HO-IP Analog Output counting is a technique for counting in an analog system. In an analog system, the signal is a continuous analog signal, so the counter needs to be able to handle the input and output of the analog signal.

The GE-8102-HO-IP analog output counter usually uses a physical quantity such as voltage or current to represent the count value. When an analog signal is input to the counter, the counter samples it, converts the analog signal to a digital signal, and counts it. The numerical value can be output through a digital interface or an analog interface, in which the digital interface usually adopts serial or parallel communication mode, while the analog interface directly outputs the analog signal.

The GE-8102-HO-IP analog output counter has the advantage of being able to interface directly with other devices in the analog system without the need for digital-to-analog conversion. At the same time, it can also provide high-precision counting values, suitable for applications requiring high-precision measurement and control. However, due to the complexity and uncertainty of the simulation system, the stability and reliability of the analog output counter may be affected to some extent.

It should be noted that analog output counters and digital output counters are different concepts, so the selection and use need to be selected according to actual application scenarios and needs.