IC660BBA026 电流源输入模块 6输入模拟电流源模块

联系电话：18059884797

产品详情

IC660BBA026 电流源输入模块 6输入模拟电流源模块

【功能描述】

IC660BBA026属于独立Block模块的Genius I/O。目前由艾默生自动化生产，GE发那科自动化已被前者收购。IC660BBA026保留了其功能，内置六(6)个模拟输入通道，支持电流源布线，分辨率为6µA。

IC660BBA026作为Genius I/O块系统的一部分，内置了Genius Bus通信接口，使该模块能够独立作为一个完整的远程I/O模块，能够通过自身配置向主控制器发送和接收I/O数据。它具有无机架设计，无需使用背板或机箱，为可用的安装方法提供最大的灵活性。这个I/O块可以安装在右侧向上或上下颠倒，在一个外壳内，提供对空气，工业污染物的保护。

IC660BBA026可配置为与同一台多插拔网络连接。如果与该模块的多个实例或同一产品系列一起使用，IC660BBA026必须相隔2英寸。此外，终端电阻必须安装在第一个和最后一个节点上，跨越串行1和串行2端子。

IC660BBA026输入通道不需要校准操作。它配备了软件可配置的诊断和。这些诊断包括低报警和高报警报告、超量程和过量程检测、断线检测和内部故障报告。该模块还提供了软件选择的输入转换时间范围从16.6 ms到400 ms。

IC660BBA026电流源输入模块是GE发那科的6输入模拟电流源模块。它可用于与输出4至20毫安模拟信号电流的设备接口。B相手持式监视器可以用来配置模块很容易。它的电压-频率转换器特性提供了一个基于所接收的模拟电流的数字信号。用户可以对各个输入电路设置上下限报警限制。输入电路由24伏额定电流回路组成，可提供25毫安电流。IC660BBA026电流源输入块具有手持式监视器，提示告警限制和诊断错误。它还具有从监视器中清除旧故障消息的功能。

IC660BBA026 电流源输入模块 6输入模拟电流源模块

IC660BBA026 belongs to Genius I/O of an independent Block module. Currently manufactured by Emerson Automation, GE Fanuc Automation has been acquired by the former. The IC660BBA026 retains its functionality with six (6) built-in analog input channels, support for current source wiring, and a resolution of 6µA.

As part of the Genius I/O block system, the IC660BBA026 has a built-in Genius Bus communication interface, enabling the module to stand alone as a complete remote I/O module, capable of sending and receiving I/O data to the master controller through its own configuration. It has a rackless design that eliminates the need for a backplane or chassis, providing maximum flexibility for available mounting methods. This I/O block can be mounted on the right side up or upside down, inside a housing that provides protection against air, industrial pollutants.

The IC660BBA026 can be configured to connect to the same multi-plug network. If used with multiple instances of the module or the same product family, the IC660BBA026 must be 2 inches apart. In addition, the terminal resistor must be installed on the first and last node, across the serial 1 and serial 2 terminals.

The IC660BBA026 input channel does not require calibration operations. It comes with software configurable diagnostics and. These diagnostics include low - and high-alarm reporting, over - and over-range detection, line break detection, and internal fault reporting. The module also provides a software-selected input conversion time range from 16.6 ms to 400 ms.

The IC660BBA026 current source input module is GE Fanuc's 6-input analog current source module. It can be used to interface with devices that output 4 to 20 mA analog signal currents. The B-phase handheld monitor can be used to configure modules easily. Its voltage-to-frequency converter features provide a digital signal based on the received analog current. Users can set upper and lower alarm limits for each input circuit. The input circuit consists of a 24-volt rated current loop that provides 25 mA. The IC660BBA026 current source input block features a handheld monitor that prompts for alarm limits and diagnostic errors. It also has the ability to clear old fault messages from the monitor.