DS200SDCCG5A 通用电气GE 驱动控制卡 有3个微处理器和RAM

DS200SDCCG5A 通用电气GE 驱动控制卡  有3个微处理器和RAM

DS200SDCCG5A 技术指标

缩写 SDCC G5A

制造者 GE汽车和工业系统

板载软件 U4、U11、U12 和 U22 的 23 个 EPROM。数量 1 EEPROM 在 U9

重量 1.5磅

系列 TC2000 汽轮机控制系统

部件号 DS200SDCCG5A

产品类型 驱动控制卡

产品描述

GE驱动器控制板DS200SDCCG5A是驱动器的主控制器。GE驱动控制板DS200SDCCG5A装有3个微处理器和RAM，可由多个微处理器同时访问。微处理器被分配了驱动控制处理中涉及的特定任务。微处理器在其上安装了执行任务所需的固件和硬件。例如，一个微处理器配备了处理功能，以执行协电机控制功能中涉及的数学计算。

DS200SDCCG5A具有五个 EPROM 连接器，用于存储配置软件。其中四个EPROM模块存储在工厂分配的配置参数。剩下的一个 EPROM 模块存储由用户或服务者分配的配置参数。GE驱动控制板DS200SDCCG5A装有EPROM连接器，但您必须使用旧板上的EPROM模块。旧主板上的模块已包含您需要的所有配置数据，因此您可以快速使驱动器重新联机。

DS200SDCCG5A还包含连接器和支架，用于连接到可用的辅助卡。您可以使用插入支架中的螺钉连接卡，然后将电缆从辅助卡连接到主板。这些卡使您能够连接到局域网，或增加电路板的信号处理能力。DS200SDCCG5A包含设置为配置板的跳线。跳线在出厂时设置，不应移动它们来改变电路板的行为。

The GE driver control board DS200SDCCG5A is the main controller of the driver. The GE drive control board DS200SDCCG5A is equipped with three microprocessors and RAM, which can be accessed by multiple microprocessors simultaneously. Microprocessors are assigned specific tasks involved in driver control processing. The microprocessor is equipped with firmware and hardware required to perform tasks. For example, a microprocessor is equipped with processing functions to perform mathematical calculations involved in co motor control functions.

The DS200SDCCG5A has five EPROM connectors for storing configuration software. Four EPROM modules are stored in factory assigned configuration parameters. The remaining EPROM module stores configuration parameters assigned by users or service providers. The GE drive control board DS200SDCCG5A is equipped with an EPROM connector, but you must use the EPROM module from the old board. The module on the old motherboard already contains all the configuration data you need, so you can quickly bring the drive back online.

The DS200SDCCG5A also includes connectors and brackets for connecting to available auxiliary cards. You can use the screws inserted into the bracket to connect the card and then connect the cable from the auxiliary card to the motherboard. These cards enable you to connect to a local area network or increase the signal processing capabilities of the circuit board. The DS200SDCCG5A contains jumpers set as configuration boards. Jumpers are set at the factory and should not be moved to change the behavior of the circuit board.