DS200SDCCG4AEC GE驱动控制板 用于为局域网添加通信功能

DS200SDCCG4AEC  GE驱动控制板 用于为局域网添加通信功能

DS200SDCCG4AEC 技术规格

制造者 通用电气通用电气

系列 马克五世

部件号 DS200SDCCG4AEC

产品类型 驱动控制卡

产品描述

GE驱动器控制板DS200SDCCG4AEC是驱动器的主控制器。GE驱动控制板DS200SDCCG4AEC装有3个微处理器和RAM，可由多个微处理器同时访问。GE驱动器控制板DS200SDCCG4AEC包含控制驱动器的所有处理功能。它还可以向其他板卡和设备发送和接收信号，以按描述执行。但是，可选卡可用于为电路板添加额外的功能。这些卡用于为局域网添加通信功能，并提供额外的信号处理能力。GE 驱动控制板 DS200SDCCG4AEC 上提供支架以连接卡。使用螺丝刀使用卡随附的螺钉连接卡。

一根或多根电缆从卡连接到主板上的连接器。如果必须更换GE驱动器控制板DS200SDCCG4AEC，则必须首先断开辅助卡的电缆，并使用螺丝刀卸下将卡固定到板上的螺钉。将螺钉、电缆和卡放在安全的地方并准备使用。当您准备好设置更换板时，请将卡连接到板并重新连接电缆。

同时从有缺陷的电路板上卸下 EPROM 模块。用拇指和食指从电路板上拉出 EPROM，然后将它们插入更换板上的连接器中。用一根手指将它们轻轻按入连接器。

The GE driver control board DS200SDCCG4AEC is the main controller of the driver. The GE drive control board DS200SDCCG4AEC is equipped with three microprocessors and RAM, which can be accessed by multiple microprocessors simultaneously. The GE driver control board DS200SDCCG4AEC contains all processing functions for controlling the driver. It can also send and receive signals to other boards and devices to execute as described. However, optional cards can be used to add additional functionality to the circuit board. These cards are used to add communication capabilities to the local area network and provide additional signal processing capabilities. A bracket is provided on the GE drive control board DS200SDCCG4AEC to connect the card. Use a screwdriver to connect the card using the screws included with the card.

Connect one or more cables from the card to the connector on the motherboard. If the GE drive control board DS200SDCCG4AEC must be replaced, the auxiliary card cable must be disconnected first and the screw that secures the card to the board must be removed using a screwdriver. Place screws, cables, and cards in a safe place and prepare for use. When you are ready to set up a replacement board, please connect the card to the board and reconnect the cables.

Simultaneously remove the EPROM module from the defective circuit board. Use your thumb and index finger to pull out the EPROM from the circuit board and insert them into the connectors on the replacement board. Gently press them into the connector with one finger.

DS200SDCCG4AEC 常见问题

DS200SDCCG4AEC测试点的目的是什么？

DS200SDCCG4AEC 的板载测试点用于测试和故障排除。

DS200SDCCG4AEC 有什么样的存储器？

DS200SDCCG4AEC 具有双端口内存。DS200SDCCG4AEC 的存储器配置为存储器阵列，可由两个 mircro 处理器独立且同时访问。

DS3SDCCG200AEC 上的 4PL 连接器的用途是什么？

DS3SDCCG200AEC 上的卡连接器 4PL 用于将 DS200SDCCG4AEC 输出到 LAN 通信卡。