DS200SDCCG3AFD GE极速创Mark V驱动控制板 用于Mark V涡轮机控制系统

DS200SDCCG3AFD  GE极速创Mark V驱动控制板  用于Mark V涡轮机控制系统

产品描述

DS200SDCCG3AFD是一款驱动控制卡，设计用于Mark V涡轮机控制系统。Mark V由通用电气制造和分销，用于管理和控制工业燃气和蒸汽轮机系统。我们公司维护MKV系统的现成库存，包括不同版本的SDCC板。确保您熟悉特定系统的正确版本。

需要知道的是，DS200SDCCG3AFD板存在触电或烧伤的潜在危险。请确保所有安装或维护此设备的员工都经过全面培训，并了解与此设备相关的危险。这是为了保持您购买的使用寿命并保护您的员工。

DS200SDCCG3AFD通过许多连接器与控制器上的其他电路板连接。与DS215SDCC板不同，该卡通常不包含带有配置数据的工厂EPROM芯片。其他电路板组件包括 TP 测试点、许多跳线开关、连接器引脚、电阻网络阵列和诊断 LED 显示屏。此显示器将以二进制编码十进制 （BCD） 或二进制形式显示故障代码。主板的用户指南和手册将为您提供有关此内容的其他信息。 GE手册也将提供有关电路板处理和安装的更多信息。

DS200SDCCG3AFD is a drive control card designed for the Mark V turbine control system. Mark V is manufactured and distributed by General Electric for the management and control of industrial gas and steam turbine systems. Our company maintains a ready-made inventory of MKV systems, including different versions of SDCC boards. Ensure that you are familiar with the correct version of a specific system.

It should be noted that the DS200SDCCG3AFD board has a potential risk of electric shock or burns. Please ensure that all employees who install or maintain this equipment have received comprehensive training and are aware of the hazards associated with this equipment. This is to maintain the service life of your purchase and protect your employees.

The DS200SDCCG3AFD is connected to other circuit boards on the controller through many connectors. Unlike the DS215SDCC board, this card often does not include factory EPROM chips with configuration data. Other circuit board components include TP test points, many jumper switches, connector pins, resistor network arrays, and diagnostic LED displays. This display will display fault codes in binary coded decimal (BCD) or binary format. The user guide and manual for the motherboard will provide you with additional information about this content. The GE manual will also provide more information on circuit board handling and installation.

关于DS200SDCIG1ABA的常见问题

是否可以在 DS200SDCIG1ABA 运行时删除 DS200SDCIG1ABA 上的连接？

不可以，当 DS200SDCIG1ABA 通电时，您不应移除 DS200SDCIG1ABA 上的连接或电路板，或将其重新插入 DS200SDCIG1ABA。否则，DS200SDCIG1ABA 可能会损坏设备。

DS1SDCIG200ABA 上的 JP1 跳线是什么？

DS1SDCIG200ABA上的跳线JP1是MD控制源跳线，允许MD接触器驱动硬件输出从属于DS200SDCIG1ABA上的MA接触器驱动硬件输出。通常在DS200SDCIG1ABA上，MD接触器驱动输出由MCP软件独立控制。

DS200SDCIG1ABA 的用途是什么？

DS200SDCIG1ABA 用于为输入电压高达 2000 VAC 的 DC600 驱动器提供逻辑电源和接口电路。