DS200SDCIG2ABA GE SDCI直流电源和仪表板 用于现场控制系统

DS200SDCIG2ABA  GE SDCI直流电源和仪表板 用于现场控制系统

DS200SDCIG2ABA 技术规格

制造者 通用电气通用电气

系列 马克五世

部件号 DS200SDCIG2ABA

产品类型 SDCI直流电源和仪表板

产品描述

GE 直流电源和仪表板 DS200SDCIG2ABA 用作 DC2000 驱动器的接口。更换DS200SDCIG2ABA时，从故障板上拔下电缆时必须小心。为避免以后在安装新主板时出现混淆，请注意故障板上所有电缆的连接位置。

DS200SDCIG2ABA不同的拆卸程序适用于各种类型的电缆。要卸下带状电缆，请勿拉动带状电缆将其拔下。相反，用一只手抓住电路板上的连接器，另一只手抓住带状电缆上的连接器，然后将两个连接器拉开。某些电缆使用卡舌固定，该卡舌将电缆连接器锁定在板上。用手指从连接器上解锁卡舌，然后从连接器上拔下电缆。卸下将某些连接器固定在主板上的所有螺钉。将螺钉放在安全的地方，以便以后安装新板时使用。

准备安装新开发板时，请单手握住DS200SDCIG2ABA，然后重新连接电缆。请参阅您所做的有关电缆连接位置的任何注释或图表。握住连接器上的带状电缆，然后将其压入板上的连接器中。确保它完全插入连接器并卡入到位。由卡舌固定的电缆在完全就位后也应卡入到位。如果用螺钉固定任何电缆，请将连接器插入电路板。然后，将螺钉插入匹配的孔中并牢固拧紧。

The GE DC power supply and instrument panel DS200SDCIG2ABA are used as interfaces for the DC2000 driver. When replacing the DS200SDCIG2ABA, care must be taken when unplugging the cable from the faulty board. To avoid confusion when installing a new motherboard in the future, please pay attention to the connection positions of all cables on the faulty board.

The different disassembly procedures of DS200SDCIG2ABA are applicable to various types of cables. To remove the ribbon cable, do not pull the ribbon cable to remove it. On the contrary, grab the connector on the circuit board with one hand and the connector on the ribbon cable with the other hand, and then pull the two connectors apart. Some cables are secured with a tab that locks the cable connector onto the board. Unlock the tab from the connector with your fingers and then unplug the cable from the connector. Remove all screws that secure certain connectors to the motherboard. Place the screws in a safe place for future installation of new boards.

When preparing to install the new development board, please hold the DS200SDCIG2ABA with one hand and reconnect the cable. Please refer to any comments or charts you have made regarding the location of cable connections. Grasp the ribbon cable on the connector and press it into the connector on the board. Ensure that it is fully inserted into the connector and clicks into place. The cable secured by the tab should also snap into place when fully seated. If any cables are secured with screws, insert the connector into the circuit board. Then, insert the screws into the matching holes and tighten them securely.

DS200SDCIG2ABA 常见问题

DS200SDCIG2ABA上的哪些电路连接到交流线路和直流电机信号？

DS200SDCIG2ABA上连接交流线路和直流电机信号的电路包括：电枢电流和电压、场电流和交流线路电流、电压幅度和相序。

DS200SDCIG2ABA 是什么版本？

DS200SDCIG2ABA 是 G2 版本的 SDCI，您可以通过 DS2SDCIG200ABA 型号中的“G2”来判断。作为G2，DS200SDCIG2ABA与外部励磁器配合使用。