IS420YDOAS1B 可以控制多达十二个继电器

IS420YDOAS1B技术指标

技术表面装配

继电器和线圈监控12继电器/线圈监视器

冗余兼容性simplex或TMR

处理器板bppc

部件编号is420ydoas1b

环境温度范围-40至158°F

I/O包响应时间6毫秒

功能缩写ydoa

尺寸:高3.25英寸x宽1.65英寸x深4.78英寸

联系电话：18059884797

立即咨询在线留言

产品详情

IS420YDOAS1B 可以控制多达十二个继电器

【功能描述】

分立输出I/O包IS420YDOAS1B可以提供多达两个以太网输入输出网络之间的电接口以及分立输出终端板。这个包可以控制多达十二个继电器，并将接受终端板特定的反馈。I/O包的所有输入将通过双以太网RJ454连接器以及三针电源输入发送。一个DC37引脚连接器用于输出，它将直接连接到相关的终端板连接器。如果需要视觉诊断，它们将通过包装前面的LED指示灯提供。

如上所述，IS420YDOAS1B I/O包可以提供诊断led;通常，12个led将是黄色的，为每个输出提供指示，指示该命令正在接通继电器。BBPx处理器led也将用于指示所需的诊断。有一个ATTN LED，将是红色或绿色，固体或闪烁。绿色ATTN LED的一些模式是2hz 50%和每四秒两个4hz脉冲;后一种模式表明应用程序是在线的，并按需运行。

在IS420YDOAS1B包运行过程中，会弹出各种常见的诊断告警，例如2、3、5。所有这些告警都有不同的原因和解决方案，告警5的描述、原因和可能的解决方案是I/O包处于远程I/O模式，一些原因是硬件故障，I/O包的模块配置可能无效，要修复这些错误，请完全更换I/O包或模块或重建系统并重新配置I/O包。

IS420YDOAS1B 可以控制多达十二个继电器

The discrete output I/O packet IS420YDOAS1B provides an electrical interface between up to two Ethernet input/output networks and a discrete output terminal board. This package can control up to twelve relays and will receive feedback specific to the terminal board. All inputs for the I/O packet will be sent via a dual Ethernet RJ454 connector as well as a three-pin power input. A DC37 pin connector is used for the output, which will be connected directly to the associated terminal board connector. If visual diagnostics are required, they will be provided via an LED indicator on the front of the package.

As mentioned above, the IS420YDOAS1B I/O package can provide diagnostic leds; Typically, 12 leds will be yellow, providing an indication for each output that the command is connecting the relay. The BBPx processor led will also be used to indicate the required diagnostics. There is an ATTN LED that will be red or green, solid or flashing. Some modes of the green ATTN LED are 2hz 50% and two 4hz pulses every four seconds; The latter pattern indicates that the application is online and running on demand.

When the IS420YDOAS1B package is running, various common diagnostic alarms are displayed, for example, alarms 2, 3, and 5. All of these alarms have different causes and solutions, the description, cause and possible solution of alarm 5 is that the I/O packet is in remote I/O mode, some of the reasons are hardware failure, the module configuration of the I/O packet may be invalid, to fix these errors, replace the I/O packet or module completely or rebuild the system and reconfigure the I/O packet.