IS420UCSCH1C 四核控制器

IS420UCSCH1C技术规格

体重约。46.8盎司

储存温度-40 ~ 85°C

系列mark VIe

内存类型4gb DDR3-1333 SDRAM

输入电压最小18 VDC至最大。30 VDC

功能缩写ucsc

高6.61英寸x深5.90英寸x宽2.17英寸

冷却方式对流冷却

联系电话：18059884797

立即咨询在线留言

产品详情

IS420UCSCH1C 四核控制器

【功能描述】

Mark VIe Controller IS420UCSCH1C是一款运行在1.2 GHz AMD g系列上的四核控制器。这个控制器是由通用电气公司制造的。作为四核控制器，该设备配备QNX Neutrino实时hypervisor多任务OS(操作系统)，可运行高速、高可靠性的工业应用。根据所使用的应用程序类型，该控制器装载了特定于模型的软件。该设备是一个BoP(工厂平衡)控制器，将运行固件和应用程序的马克VIe系列利用IONet接口。IONet接口被标记为专用的专用以太网接口，它只支持Mark控制I/O控制器和包。

许多(如果不是所有)未标记为UCSC控制器的其余控制器在背板上使用I/O, IS420UCSCH1C控制器不使用这种类型的应用程序，并且不具有承载任何I/O应用程序的能力。如果这个控制器在冗余集中使用，所有附加的I/O网络将向所有附加的控制器发送输入数据。该控制器上的软件和硬件有能力保证，如果控制器因维护或修理而关闭，不会丢失单点应用程序输入。

挂载IS420UCSCH1C控制器时需要满足要求。安装控制器时，确保使用两个安装螺钉将其直接安装到所选的安装底座上，请注意，UCSC上方和下方需要至少四英寸的气流。

IS420UCSCH1C 四核控制器

The Mark VIe Controller IS420UCSCH1C is a quad-core controller running on the 1.2GHz AMD g series. The controller was made by General Electric. As a quad-core controller, the device is equipped with the QNX Neutrino real-time hypervisor multitasking OS(operating system) to run high-speed, highly reliable industrial applications. Depending on the type of application being used, the controller is loaded with model-specific software. The device is a BoP(Factory Balance) controller that will run firmware and applications from the Mark VIe family utilizing the IONet interface. The IONet interface is labeled as a dedicated dedicated Ethernet interface that only supports Mark control of I/O controllers and packets.

Many, if not all, of the remaining controllers that are not labeled as UCSC controllers use I/O on the backplane, and the IS420UCSCH1C controller does not use this type of application and does not have the ability to host any I/O applications. If this controller is used in a redundant set, all additional I/O networks will send input data to all additional controllers. The software and hardware on this controller have the capability to guarantee that a single point of application input will not be lost if the controller is shut down for maintenance or repair.

The IS420UCSCH1C controller must meet these requirements. When installing the controller, make sure to use two mounting screws to mount it directly onto the selected mounting base, noting that at least four inches of air flow is required above and below the UCSC.