IS420UCPAH2A两个控制器程序中的第二个

IS420UCPAH2A技术规格

端子座螺丝扭矩4.55 in-lb

不支持共享网络

内存64mb

功耗4w

部件编号is420ucpah2a

安装方法底座安装

模拟输出电压0- 10v

内部操作系统qnx

输入电压12vdc

扩展板is400wexph1a

配置软件工具箱应用程序

联系电话：18059884797

立即咨询在线留言

产品详情

IS420UCPAH2A两个控制器程序中的第二个

【功能描述】

产品描述

IS420UCPAH2A模块是通用电气生产的Mark VIe系列中具有积分I/ o的两个控制器程序中的第二个。该控制器几乎与以前的UCPA控制器相同，用于IS400WEXPH1A扩展I/O板，允许额外的I/O功能。这个控制器上的额外I/O功能是4个额外的dio，总共8个;另外6个ai，总计8个，还有2个模拟输出。与前一个控制器相同，该控制器上的输入输出点也具有按点配置的能力。

安装后，IS420UCPAH2A控制器直接安装在钣金面板上，并包含在单个模块中。当操作正常时，控制器将运行在12伏直流电的标称电源上，在9至16伏直流电的范围内。输入电源将由II级保护级别供电。当连接控制器输入端子时，请确保它们的长度不超过98英尺。

IS420UCPAH2A控制器有几个LED, DIO1-8，脉冲1和2，以及一个注意LED。DIO和Pulse LED将是纯黄色，但注意力LED将是红色和绿色，并带有多个闪烁代码。有绿色和红色的ATTN LED闪烁代码，其中一些如下，一个红色的四赫兹LED在50%表示诊断警报是活跃的，一个红色的一赫兹LED在50%表示没有固件可用，一个绿色的一/二赫兹LED在50%表示组件已经完成上电。

正确操作IS420UCPAH2A控制器所需的所有信息都位于GEI-10071 Mark VIe控制器UCPA指令指南中。

IS420UCPAH2A两个控制器程序中的第二个

Product description

The IS420UCPAH2A module is the second of two controller programs with integrated I/ o in the Mark VIe series produced by General Electric. This controller is almost identical to the previous UCPA controller for the IS400WEXPH1A extended I/O board, allowing for additional I/O functionality. The additional I/O functionality on this controller is 4 additional DIOs for a total of 8; Another six ai, eight in total, and two analog outputs. As with the previous controller, the input/output points on this controller also have the ability to be configured point-to-point.

After installation, the IS420UCPAH2A controller is installed directly on the sheet metal panel and is contained in a single module. When operating properly, the controller will run on a nominal power supply of 12 volts DC, in the range of 9 to 16 volts DC. The input power will be powered by the Level II protection level. When connecting controller input terminals, make sure they are no longer than 98 feet.

The IS420UCPAH2A controller has several leds, DIO1-8, pulses 1 and 2, and an attention LED. The DIO and Pulse leds will be solid yellow, but the attention leds will be red and green with multiple flashing codes. There are green and red ATTN LED flashing codes, some of which are as follows, a red 4 Hz LED at 50% indicates that the diagnostic alert is active, a red 1 Hz LED at 50% indicates that no firmware is available, and a green 1/2 Hz LED at 50% indicates that the component has finished powering on.

All the information needed to properly operate the IS420UCPAH2A controller is located in the GEI-10071 Mark VIe Controller UCPA Instruction Guide.