IS420UCPAH1A 输入输出的控制器平台

IS420UCPAH1A技术规范

型号is420ucpah1a

冗余类型

处理器类型飞思卡尔3308处理器

功耗4w

工作温度-40 ~ 70℃

安装方法底座安装

内存类型ram, NOVRAM和板载闪存

输入电压12vdc

尺寸高6.3英寸x宽4.5英寸x深2.8英寸

联系电话：18059884797

立即咨询在线留言

产品详情

IS420UCPAH1A 输入输出的控制器平台

【功能描述】

Mark VIe IS420UCPAH1A设备是一个具有积分输入输出的控制器平台。该设备的核心功能是运行控制逻辑，也称为应用程序代码。该模块的一个关键特性是，由于其集成I/O功能，它可以通过简单的IONet功能与外部输入输出数据包进行通信。请注意，虽然这个控制器对所有人都可以使用，但它只能用于商业设计，而不能用于任何类型的住宅环境。

这个模型是UCPA模型中的第一个。作为第一款，IS420UCPAH1A型号配备了一个BPPCH2A处理器板以及一个基础IS400STWCH1A I/O板。有了这些功能，控制器将提供以下输入和输出，两个模拟输入(ai)，四个带反馈的数字输入/输出(dio)和两个霍尔效应脉冲输入。根据所使用的I/O点，可以按每个点配置它们。

IS420UCPAH1A上有led，由BPPC处理器板提供。DIO1到DIO8 led将是黄色的，表示分立的IOs在低功能下开启和激活;PULSE1和PULSE2 led也将是黄色，表明脉冲输入在低功能下开启和激活。还有一种关注LED，标为ATTN，是一种红绿双色LED;绿色表示提供同步，红色表示提供关注。

IS420UCPAH1A控制器需要特定的固件才能正常运行，在最佳情况下，获得此固件所需的固件是Mark VIe V05.04.03C。操作该控制器所需的所有信息都可以在GEI-100719 Mark VIe UCPA控制器指导指南中找到。

IS420UCPAH1A 输入输出的控制器平台

The Mark VIe IS420UCPAH1A device is a controller platform with integral input and output. The core function of the device is to run control logic, also known as application code. A key feature of the module is that, thanks to its integrated I/O capabilities, it can communicate with external input-output packets via a simple IONet function. Please note that while this controller is available to everyone, it can only be used in commercial designs and not in any type of residential environment.

This model is the first of its kind in UCPA. As the first, the IS420UCPAH1A model is equipped with a BPPCH2A processor board and a base IS400STWCH1A I/O board. With these features, the controller will provide the following inputs and outputs, two analog inputs (ai), four digital inputs/outputs with feedback (dio), and two Hall-effect pulse inputs. Depending on which I/O points are used, they can be configured on a per-point basis.

The IS420UCPAH1A has leds, which are provided by the BPPC processor board. DIO1 through DIO8 leds will be yellow, indicating that discrete IOs is turned on and activated with low functionality; The PULSE1 and PULSE2 leds will also be yellow, indicating that the pulse input is turned on and activated at low function. There is also a concern LED, labeled ATTN, is a red and green two-color LED; Green for synchronization and red for attention.

The IS420UCPAH1A controller requires specific firmware to function properly, and in the best case scenario, the firmware needed to get this firmware is Mark VIe V05.04.03C. All the information needed to operate this controller can be found in the GEI-100719 Mark VIe UCPA Controller Guidance Guide.