IS420ESWBH5A ESWB硬件的第五版

IS420ESWBH5A技术指标

通用电气能源公司

体重1磅8盎司

产品类型标识VIe网络交换机

部件编号is420eswbh5a

工作振动1.0 G水平，0.5 G垂直

工作温度-40至+158°F

绝对最大电流< 1.0 A

输入电压28vdc

功能缩写eswb

光纤接口2、100Base-LX10单模光纤接口

尺寸高18.8厘米×宽8.6厘米×深5.6厘米

保形涂层耐腐蚀

联系电话：18059884797

立即咨询在线留言

产品详情

IS420ESWBH5A ESWB硬件的第五版

【功能描述】

IS420ESWBH5A IONet Switch是ESWB硬件的第五版，也是最终版。本交换机除光纤接口外，其他型号基本相同，有2个光纤接口。本交换机的两个光纤端口为100Base-LX10单模光纤端口，采用lc型连接;请注意，由于这些端口是单模光纤端口，需要额外的单模传感器;这个换能器的零件号是65G2100-008，是通用电气公司生产的。

这个包的操作主要集中在缓冲包的能力上。IS420ESWBH5A包被认为是一级以太网交换机，具有连续的多播和/或广播数据包流，可以缓冲传入的流，并在完全接收后将其发送出去。请注意，当多个流进入时，一次只能释放一个流，所有剩余的流将在以后的时间被缓冲。

这种开关有能力安装在多个位置，危险和非危险一样，以及在两个不同的方向。IS420ESWBH5A开关的危险场所为一类，二区;二级，二区和ATEX。该开关将安装在din导轨上，并放置在与导轨平行或垂直的开关长边缘上。当并联安装时，需要259B2451BVP1夹。如果在第三方场合更换交换机，交换机可以采用面板安装方式，面板安装时使用的螺钉与前一个部件相同。

IS420ESWBH5A ESWB硬件的第五版

IS420ESWBH5A Technical Specifications

Manufacturer	GE Energy
Weight	1lbs 8oz
Product Type	Mark VIe IONet Switch
Part Number	IS420ESWBH5A
Operating Vibration	1.0 G Horizontal, 0.5 G Vertical
Operating Temperature	-40 to +158 °F
Absolute Max Current	< 1.0 A
Input Voltage	28 VDC
Functional Abbreviation	ESWB
Fiber Ports	2, 100Base-LX10 Single-Mode Fiber Ports
Dimensions	H 18.8 cm x W 8.6 cm x D 5.6 cm
Conformal Coating	Resistant to Corrosion

The IS420ESWBH5A IONet Switch is the fifth and final version of the ESWB hardware. This switch is the same as the previous models except for its fiber ports, this switch has two fiber ports. The two fiber ports on this switch are 100Base-LX10 single-mode fiber ports with LC-type connection; please note that as these ports are single-mode fiber ports an additional single-mode transducer is required; the part number for this transducer is 65G2100–008 which is manufactured by General Electric.

The operation for this pack is mainly centered on the ability to buffer packets. The IS420ESWBH5A pack is considered a level-one Ethernet switch and will have a continuous stream of multicast and/or broadcast packets that will buffer incoming streams and send them out upon complete reception. Please note that when multiple streams are coming in only one stream can be relieved at a time, all of the remaining streams will have to be buffered at a later time.

This switch has the ability to be mounted in multiple locations, hazardous and non-hazardous alike as well as in two different orientations. The hazardous locations for the IS420ESWBH5A switch are class one, division two; class two, zone two, and ATEX. The switch will be DIN-rail mounted and positioned on the long edge of the switch either parallel or perpendicular to the rail. When parallel mounted a 259B2451BVP1 clip is required. If this switch is replacing another in a third-party situation the switch can be panel mounted, panel mounting will use the screws that were used with the previous part.