DS200SDCIG1AEB 电源板 具有用于电机磁场电源电路的电路

DS200SDCIG1AEB  电源板  具有用于电机磁场电源电路的电路

DS200SDCIG1AEB 技术规格

制造者 通用电气通用电气

系列 马克五世

部件号 DS200SDCIG1AEB

产品类型 SDCI直流电源和仪表板

产品描述

GE 直流电源和仪表板 DS200SDCIG1AEB 用作 DC2000 驱动器的接口。DS200SDCIG1AEB装有5个保险丝，用于保护电路板免受损坏。如果发生电源过载情况，保险丝可能会熔断以保护组件免受损坏。一个有价值的功能是，如果保险丝熔断，您可以检查板上的 LED 灯并确认电路板发生了问题。您可以参考电路板附带的信息并确定保险丝熔断的可能原因。

您可以确定必须立即更换DS200SDCIG1AEB主板，或者可以确定驱动器中的某种情况导致主板出现故障。如果是这种情况，请先更正驱动器中的条件。例如，临时过载情况导致保险丝熔断。在这种情况下，如果暂时过载情况不太可能再次发生，只需从驱动器上卸下电路板，更换保险丝，重新安装电路板并继续制造过程。

您只能允许合格的维修人员检查、修理或以其他方式触摸主板或安装它的驱动器。这也适用于更换熔断的保险丝。服务人员必须熟悉制造现场的设备，特别是驱动器和电路板。不合格的服务商可能会损坏组件或将组件暴露在危险的高压下。不合格的服务可能会因高压电流而受损。

The GE DC power supply and instrument panel DS200SDCIG1AEB are used as interfaces for the DC2000 driver. The DS200SDCIG1AEB is equipped with 5 fuses to protect the circuit board from damage. If a power overload occurs, the fuse may blow to protect the component from damage. A valuable feature is that if the fuse blows, you can check the LED lights on the board and confirm that there is a problem with the circuit board. You can refer to the information provided with the circuit board and determine the possible cause of the fuse blowing.

You can confirm that the DS200SDCIG1AEB motherboard must be replaced immediately, or you can confirm that some condition in the drive is causing the motherboard to malfunction. If this is the case, please correct the conditions in the drive first. For example, a temporary overload situation may cause a fuse to blow. In this case, if the temporary overload situation is unlikely to occur again, simply remove the circuit board from the driver, replace the fuse, reinstall the circuit board, and continue the manufacturing process.

You can only allow qualified maintenance personnel to inspect, repair, or otherwise touch the motherboard or install its drive. This also applies to replacing a blown fuse. Service personnel must be familiar with the equipment on the manufacturing site, especially drivers and circuit boards. Unqualified service providers may damage components or expose them to dangerous high voltage. Unqualified services may be damaged due to high voltage currents.

DS200SDCIG1AEB 常见问题

DS200SDCIG1AEB的供电电路适用于哪些？

DS200SDCIG1AEB 具有电源电路：+5 VDC、4A;+/-15 伏直流电，0.4 安;+/-24 伏直流和 115 伏交流电，0.4 安。DS200SDCIG1AEB还具有用于电机磁场电源电路的电路。

DS3SDCIG200AEB 上的保险丝“FU1”有什么用？

DS3SDCIG200AEB 上的保险丝“FU1”是用于 -24 和 -5 VDC 信号电平电源的保险丝。如果DS3SDCIG200AEB上的保险丝“FU1”熔断，编程器无法处理故障信息，但当控制电源施加到驱动器时，LED CR55将亮起。当DS3SDCIG200AEB上的“FU1”保险丝熔断时，通常是因为探测时或端子板上的接线错误意外短路-24V。

DS200SDCIG1AEB上的哪些电路连接到交流线路和直流电机信号？

DS200SDCIG1AEB上用于检测大量交流线路和直流电机信号的电路包括：电枢电流和电压、励磁电流和交流线路电流、电压幅度和相序。