369-HI-R-M-F-0-H-E 369电机保护继电器

369-HI-R-M-F-0-H-E技术规范

控制功率范围110至250 VDC, 100至240 VAC在50/60 Hz

差动开关延时< 200ms

尺寸约:29.6厘米高× 10.7厘米宽× 20.5厘米长

i级绝缘

相电流二次输入1a和5a

RTD输入3根线，100根Ω铂，100根Ω镍，120根Ω镍，10根Ω铜

体重约。10磅

联系电话：18059884797

立即咨询在线留言

产品详情

369-HI-R-M-F-0-H-E 369电机保护继电器

【功能描述】

369-HI-R-M-F-0-H-E技术规范

控制功率范围110至250 VDC, 100至240 VAC在50/60 Hz

差动开关延时< 200ms

尺寸约:29.6厘米高× 10.7厘米宽× 20.5厘米长

i级绝缘

相电流二次输入1a和5a

RTD输入3根线，100根Ω铂，100根Ω镍，120根Ω镍，10根Ω铜

体重约。10磅

产品描述

通用电气Multilin的369- hi - r - m - f -0- h - e是369电机保护继电器。该系列继电器旨在保护电机(三相)和相关系统，同时在两个控制输入功率级别提供许多基本功能和选项。虽然这些组件现在已经进入遗留状态，不能从OEM购买，但AX Control致力于保持尽可能多的型号库存。这使我们能够迅速完成您的订单。大多数现货产品发货时间不到24小时，许多甚至不到两小时。

369-HI-R-M-F-0-H-E提供了许多选择。这包括12个RTD输入。RTD单元位于单元的左侧后方。这个单位也有一个可选的计量包。计量包增加了访问VT输入，将允许电压和功率元件。计量赫兹，千伏安，千瓦，伏特和兆瓦时是可能的，与此选项。

369-LO-0-M-F-E-0还安装了一个额外的光纤端口。光纤端口波特率为1200 ~ 19200，采用Modbus RTU协议。这用于通道3。当用于通道3时，通道3 RS485连接被禁用。然而，该单元仍将有其他RS485端口可用。此外，该设备有一个RS232端口，可用于连接PC。这通常用于与通用电气的EnerVista软件进行通信。

有关此版本的369继电器的其他信息，或有关369安装，处理或维护的一般信息，可通过GE手册和用户指南找到。

369-HI-R-M-F-0-H-E 369电机保护继电器

369-HI-R-M-F-0-H-E Technical specification

Control power range 110 to 250 VDC, 100 to 240 VAC at 50/60 Hz

Differential switch delay < 200ms

Dimensions :29.6 cm high x 10.7 cm wide x 20.5 cm long

Class i insulation

Phase current secondary input 1a and 5a

RTD Input 3 wires, 100 Ω platinum, 100 Ω nickel, 120 Ω nickel, and 10 Ω copper

Weighs about. Ten pounds

Product description

General Electric Multilin's 369-HI-R-M-F-0-H-E is a 369 motor protection relay. This series of relays is designed to protect the motor (three-phase) and associated systems while providing many basic features and options in both control input power levels. While these components are now in legacy status and cannot be purchased from Oems, AX Control is committed to keeping as many models in stock as possible. This allows us to complete your order quickly. Most off-the-shelf products ship in less than 24 hours, and many in less than two hours.

The 369-HI-R-M-F-0-H-E offers a number of options. This includes 12 RTD inputs. The RTD unit is located on the left rear of the unit. This unit also has an optional metering package. The metering package adds access to VT inputs that will allow voltage and power components. Metering Hertz, kilovolt ampere, kilowatt, volt and megawatt-hour is possible with this option.

The 369-LO-0-M-F-E-0 also has an additional fiber optic port installed. The baud rate of the optical fiber port ranges from 1200 to 19200, and Modbus RTU is used. This is used for channel 3. When used in channel 3, the RS485 connection in channel 3 is disabled. However, the unit will still have other RS485 ports available. In addition, the device has an RS232 port that can be used to connect to a PC. This is commonly used to communicate with General Electric's EnerVista software.

Additional information about this version of the 369 relay, or general information about 369 installation, handling, or maintenance, can be found in GE manuals and user guides.