DS200TCQCG1BGF rst溢出板

DS200TCQCG1BGF技术规范

制造商ge通用电气

系列mark V

部件编号ds200tcqcg1a

产品类型rst溢出板

联系电话：18059884797

立即咨询在线留言

产品详情

DS200TCQCG1BGF rst溢出板

【功能描述】

DS200TCQCG1BGF技术规范

制造商ge通用电气

系列mark V

部件编号ds200tcqcg1a

产品类型rst溢出板

产品描述

GE RST溢出板DS200TCQCG1BGF由24个跳线和3个40针连接器组成。它也有3个34针连接器和1个16针连接器。分配给16针连接器的ID是JC。分配给40针连接器的id是JFF、JE和6PL。GE RST溢出板DS200TCQCG1BGF上的跳线使安装人员能够根据设备的确切需求配置该板。安装原始电路板时，安装人员将查看随电路板提供的安装指南中的信息。它包含对跳线的描述，以及跳线的位置如何改变板的处理方式。通过与设施工程人员协商，安装人员可以设置跳线以更好地满足设施的要求。这是驱动器安装过程的一部分，可能需要安装人员与工厂代表进行一些安装前的沟通，以决定如何最好地设置跳线。

然而，一旦完成，跳线保持在原位，不需要进一步配置。当您计划更换由于安装的板有缺陷的板时，这是特别有用的。唯一需要的配置是将替换板上的跳线设置为与旧板上的跳线位置匹配。要做到这一点，把旧板放在平坦干净的表面上。然后佩戴好防静电腕带，将单板从密封的防静电包装袋中取出。将板放在旧板旁边，比较跳线位置。

DS200TCQCG1BGF常见问题解答

DS200TCQCG1BGF需要操作哪些板?

为了使DS200TCQCG1BGF正常工作，DS200TCQCG1BGF需要TCQA和TCQB。

DS200TCQCG1BGF有多少个DENET连接?

DS200TCQCG1BGF有两个DENET连接，为DENET建立了一个六端口无源桥接。

DS200TCQCG1BGF给LVDT带来了什么?

LVDT需要由DS200TCQCG1BGF提供的激励器电压。

在DS200TCQCG1BGF上进行什么转换?

在DS200TCQCG1BGF上实现了高速标志v控制系统的数模转换。DS200TCQCG1BGF完成的这种转换代表了所需的燃油流量。

DS200TCQCG1BGF rst溢出板

DS200TCQCG1BGF technical specification

Manufacturer ge General Electric

Series mark V

Part number ds200tcqcg1a

Product Type rst overflow board

Product description

The GE RST overflow board DS200TCQCG1BGF consists of 24 jumpers and 3 40-pin connectors. It also has three 34-pin connectors and one 16-pin connector. The ID assigned to the 16-pin connector is JC. The ids assigned to 40-pin connectors are JFF, JE, and 6PL. Jumpers on the GE RST overflow board DS200TCQCG1BGF enable the installer to configure the board according to the exact requirements of the device. When installing the original board, the installer will review the information in the installation guide provided with the board. It contains a description of the jumpers and how the position of the jumpers changes the way the board is handled. In consultation with facility engineers, installers can set up jumpers to better meet the requirements of the facility. This is part of the drive installation process and may require some pre-installation communication between the installer and the factory representative to decide how best to set up the jumper.

However, once completed, the jumper remains in place and no further configuration is required. This is especially useful when you plan to replace a board that is defective due to an installed board. The only configuration required is to set the jumper on the replacement board to match the jumper position on the old board. To do this, place the old board on a flat, clean surface. Then wear an ESD wrist strap and take the board out of the sealed ESD bag. Place the board next to the old board and compare the jumper position.

DS200TCQCG1BGF Frequently Asked Questions

Which boards do DS200TCQCG1BGF need to operate?

In order for the DS200TCQCG1BGF to work properly, the DS200TCQCG1BGF requires TCQA and TCQB.

How many DENET connections does DS200TCQCG1BGF have?

The DS200TCQCG1BGF has two DENET connections and establishes a six-port passive bridge for the DENET.

What does DS200TCQCG1BGF bring to the LVDT?

The LVDT requires the driver voltage provided by the DS200TCQCG1BGF.

What conversion on DS200TCQCG1BGF?

The digital to analog conversion of high speed mark v control system is realized on DS200TCQCG1BGF. This conversion done by the DS200TCQCG1BGF represents the required fuel flow.