DS200TCQAG1BHF 模拟I/O板

制造商ge通用电气

系列mark V

部件编号ds200tcqag1bhf

产品类型模拟I/O板

联系电话：18059884797

立即咨询在线留言

产品详情

DS200TCQAG1BHF 模拟I/O板

【功能描述】

DS200TCQAG1BHF技术规范

制造商ge通用电气

系列mark V

部件编号ds200tcqag1bhf

产品类型模拟I/O板

产品描述

GE RST模拟I/O板DS200TCQAG1BHF包含四个34针连接器，两个40针连接器和六个跳线。该板也有6个led。GE RST模拟I/O板DS200TCQAG1BHF设计了6个孔，用于将板安装在驱动器上的板柜中。这些孔与板架上的匹配孔对齐，您可以用垫圈和螺钉连接板。拆卸旧单板时，请将垫圈和螺钉固定在一起，以便在安装新单板时使用。由于单板内电压较高，所以一定不要让任何金属部件落入单板柜中。如果螺钉或垫圈掉落在机柜中，请找到该部件并将其从驱动器中取出。如果驱动器启动时松散的金属仍在内部，金属可能会损坏驱动器或引发火灾或导致严重的电击。

有一些指导方针可以帮助防止金属螺钉和垫圈在驱动器中掉落。拆卸单板时，一只手握住螺丝刀，另一只手将螺丝刀对准螺钉，在拆卸单板时握住螺钉。安装螺钉时，一只手将螺钉对准孔位，另一只手转动螺丝刀。不要过度拧紧螺丝，因为木板可能会破裂或断裂。相反，只需拧紧螺丝到位。垫圈有助于防止由于过度拧紧而损坏电路板。

关于DS200TCQAG1BHF的常见问题

是否有DS200TCQAG1BHF的说明书?

是的，手动GEH-6353，马克V LM涡轮控制手册在手册的第5-4节中描述了DS200TCQAG1BHF。我们目前没有DS200TCQAG1BHF的具体手册，但我们可以向您发送manual GEH-6353，以帮助处理DS200TCQAG1BHF的连接、软件、硬件等。

DS200TCQAG1BHF和STCA之间的数据总线是哪个连接器?

DS200TCQAG1BHF和STCA之间的数据总线连接器是DS200TCQAG1BHF上的连接器3PL。条件信号在DS200TCQAG1BHF上的3PL上传输，并传输到COREBUS。

DS200TCQAG1BHF做什么?

DS200TCQAG1BHF对安装在I/O内核< R1 >、< R2 >和< R3 >上的终端板读取的许多模拟信号进行缩放和调节。

DS200TCQAG1BHF 模拟I/O板

DS200TCQAG1BHF technical specification

Manufacturer ge General Electric

Series mark V

Component number ds200tcqag1bhf

Product Type Analog I/O board

Product description

The GE RST analog I/O board DS200TCQAG1BHF contains four 34-pin connectors, two 40-pin connectors, and six jumpers. The board also has 6 leds. The GE RST analog I/O board DS200TCQAG1BHF is designed with 6 holes for mounting the board in the board cabinet on the driver. These holes are aligned with the matching holes in the board frame, and you can attach the board with washers and screws. When removing the old board, secure the washers and screws together so that they can be used when installing the new board. Due to the high voltage in the board, be sure not to let any metal parts fall into the board cabinet. If a screw or washer falls in the cabinet, locate the part and remove it from the drive. If the loose metal is still inside the drive when it starts, the metal can damage the drive or start a fire or cause a severe electric shock.

There are some guidelines that can help prevent metal screws and washers from falling off in the drive. When removing the board, hold the screwdriver with one hand, align the screwdriver with the screw with the other hand, and hold the screw when removing the board. When installing a screw, align the screw with the hole with one hand and turn the screwdriver with the other hand. Do not over-tighten the screws, as the board may crack or break. Instead, simply tighten the screws in place. Washers help prevent damage to the board due to over-tightening.

Frequently asked questions about DS200TCQAG1BHF

Is there a manual for DS200TCQAG1BHF?

Yes, manual GEH-6353, Mark VLM Turbine Control Manual describes DS200TCQAG1BHF in sections 5-4 of the manual. We do not currently have a specific manual for the DS200TCQAG1BHF, but we can send you a Manual GEH-6353 to help with connection, software, hardware, etc., for the DS200TCQAG1BHF.

Which connector is the data bus between the DS200TCQAG1BHF and STCA?

The data bus connector between the DS200TCQAG1BHF and STCA is the connector 3PL on the DS200TCQAG1BHF. The conditional signal is transmitted over 3PL on the DS200TCQAG1BHF and is transmitted to COREBUS.

What does DS200TCQAG1BHF do?

The DS200TCQAG1BHF scales and adjusts many analog signals read from the end boards installed on the I/O cores < R1 >, < R2 >, and < R3 >.