DS200TBQCG1AAA 模拟终端板

部件编号ds200tbqcg1aaa

系列mark V

制造商ge通用电气

使用说明书geh -6153

产品类型rst模拟终端板

功能缩写tbqc

TBQC连接数5;JBR、JFR、TEST、JBS/T和JFS/T

联系电话：18059884797

立即咨询在线留言

产品详情

DS200TBQCG1AAA 模拟终端板

【功能描述】

DS200TBQCG1AAA技术规范

部件编号ds200tbqcg1aaa

系列mark V

制造商ge通用电气

使用说明书geh -6153

产品类型rst模拟终端板

功能缩写tbqc

TBQC连接数5;JBR、JFR、TEST、JBS/T和JFS/T

产品描述

GE RST模拟终端板DS200TBQCG1AAA具有两个端子排。每个模块包含83个用于信号线的端子。GE RST模拟终端板DS200TBQCG1AAA还包含15个跳线，3个40针连接器和3个34针连接器。跳线使服务人员能够修改电路板的行为，以满足驱动器操作的确切要求。当您第一次安装电路板并从工厂收到电路板时，请参阅安装说明，其中包括对跳线的描述以及跳线的位置如何修改电路板的操作。当你收到单板时，跳线处于默认位置。默认值用于大多数情况，如果您只需要默认值，则不需要额外的步骤。

3针跳线很容易从默认位置移动到备用位置。用你的食指和拇指从默认位置移除跳线。然后将跳线对准备用引脚并按下跳线到位。例如，如果引脚1和2是3引脚跳线的默认位置，则将跳线插入引脚2和3以使用备用位置。

DS200TBQCG1AAA机组上的一些跳线仅供工厂使用，不能更改。通常情况下，替代职位仅用于工厂的质量控制测试目的。当更换电路板时，首先将更换板上的跳线移动到与故障板上的位置匹配。

DS200TBQCG1AAA常见问题解答

DS200TBQCG1AAA有什么类型的输出信号?

DS200TBQCG1AAA板上的信号为毫安输出信号。这些信号将进入或来自其各自核心的附加TCQA板。与此模型和TCQA板相关的输出类型是20-200 mA输出。

DS200TBQCG1AAA上的输入信号是什么?

DS200TBQCG1AAA板的输入信号与输出信号相同，均为毫安信号。该板上可用的毫安信号是LVDT/R位置输入和4-20 mA到附加的TCQA及其各自的核心。

DS200TBQCG1AAA上的跳线BJ1到BJ15是什么?

DS200TBQCG1AAA上的BJ1 ~ BJ15跳线用于连接DS200TBQCG1AAA上的毫安输入信号1-15至DCOM。

DS200TBQCG1AAA 模拟终端板

DS200TBQCG1AAA technical specification

Part number ds200tbqcg1aaa

Series mark V

Manufacturer ge General Electric

Instruction manual geh-6153

Product Type rst Analog terminal board

Function abbreviation tbqc

TBQC connection number 5; JBR, JFR, TEST, JBS/T and JFS/T

Product description

The GE RST analog terminal board DS200TBQCG1AAA has two terminal blocks. Each module contains 83 terminals for signal lines. The GE RST Analog terminal board DS200TBQCG1AAA also contains 15 jumpers, three 40-pin connectors, and three 34-pin connectors. Jumpers enable service personnel to modify the behavior of the board to meet the exact requirements of driver operation. When you install the board for the first time and receive the board from the factory, refer to the installation instructions, which include a description of the jumpers and how the location of the jumpers modifies the operation of the board. When you receive the board, the jumper is in the default position. The default values are used in most cases, and if you only need the default values, no additional steps are required.

The 3-pin jumper is easily moved from the default position to the standby position. Use your index finger and thumb to remove the jumper from the default position. Then align the jumper with the spare pin and press the jumper into place. For example, if pins 1 and 2 are the default positions for 3-pin jumpers, insert the jumpers into pins 2 and 3 to use the alternate positions.

Some jumpers on the DS200TBQCG1AAA unit are for factory use only and cannot be changed. Typically, replacement positions are only used for quality control testing purposes at the plant. When replacing the board, first move the jumper on the replacement board to match the position on the faulty board.

DS200TBQCG1AAA Frequently Asked Questions

What type of output signal does the DS200TBQCG1AAA have?

The signal on the DS200TBQCG1AAA board is a MA output signal. These signals will enter or come from additional TCQA boards in their respective cores. The output type associated with this model and TCQA board is 20-200 mA output.

What is the input signal on the DS200TBQCG1AAA?

The input signal of the DS200TBQCG1AAA board is the same as the output signal, which is a MA signal. The mA signal available on this board is the LVDT/R position input and 4-20 mA to the attached TCQA and its respective cores.

What are the jumpers BJ1 to BJ15 on DS200TBQCG1AAA?

The BJ1 to BJ15 jumpers on the DS200TBQCG1AAA are used to connect the MA input signal 1-15 on the DS200TBQCG1AAA to the DCOM.