DS200SDCIG2AEB 驱动器的接口

制造商ge通用电气

系列mark V

部件编号ds200sdcig2aeb

产品类型sdci直流电源及仪表板

使用说明书gei -100173

联系电话：18059884797

立即咨询在线留言

产品详情

DS200SDCIG2AEB 驱动器的接口

【功能描述】

DS200SDCIG2AEB技术规范

制造商ge通用电气

系列mark V

部件编号ds200sdcig2aeb

产品类型sdci直流电源及仪表板

使用说明书gei -100173

产品描述

GE直流电源和仪表板DS200SDCIG2AEB作为DC2000驱动器的接口。DS200SDCIG2AEB是一种静电敏感器件，在触摸、维护和安装设备时必须小心。静电会通过空气、接触设备的人员、接触其他设备和结构等途径积聚在单板上。静电会损坏单板上的敏感元器件，导致单板无法使用。

如果需要对单板进行维护，请将单板放在平整干净的表面上，并在接触单板之前佩戴好接地带。接地带可以防止静电积聚。

走路和触摸物品会导致静电积聚，所以在使用电路板之前最好不要移动太多。当你做处理板只持有它的边缘，永远不要触摸焊点或组件。在准备安装之前，将其从包装中取出，触摸未涂漆的金属表面，以排出任何静电。只有这样，才可以安全安装更换后的单板。

如果单板从包装袋中取出后必须放下，请将单板放在空的防静电包装袋上。

DS200SDCIG2AEB上的电容器即使在断开电流后也能存储高压电流，因此在触摸电路板之前测试电路板的电流是很重要的，以防止电烧伤和触电。

关于DS200SDCIG2AEB的常见问题

DS200SDCIG2AEB使用哪本手册?

DS200SDCIG2AEB使用的手册是通用电气驱动系统更换程序SDCI直流电源和仪表板手册。虽然本手册是基于用另一块DS200SDCIG2AEB板替换DS200SDCIG2AEB的手册，但该手册提供了额外的信息，以帮助您了解DS200SDCIG2AEB。

DS200SDCIG2AEB上使用的JP2跳线是什么?

DS200SDCIG2AEB上的JP2跳线是DS200SDCIG2AEB的MA交流接触器断开时间跳线。一般来说，DS200SDCIG2AEB上的电路延迟交流接触器的打开，以确保DS200SDCIG2AEB上的所有负载电流已熄灭。在DS200SDCIG2AEB正常运行时移除跳线JP2会导致控制电路在电流为0之前断开MA继电器。

DS200SDCIG2AEB 驱动器的接口

DS200SDCIG2AEB Technical Specifications

Manufacturer GE General Electric

Series Mark V

Part Number DS200SDCIG2AEB

Product Type SDCI DC Power Supply and Instrumentation Board

Instruction Manual GEI-100173

Product Description

The GE DC Power Supply and Instrumentation Board DS200SDCIG2AEB serves as an interface to DC2000 drives. The DS200SDCIG2AEB is a static-sensitive device and care must be taken when touching, maintaining, and installing the device. Static electricity can accumulate on the board through the air, persons touching the device, and when the device comes in contact with other device and structures. The static electricity can damage sensitive components on the board and lead the board to being unuseable.

If you plan to maintain the board, place the board on a flat clean surface and wear a grounding strap before touching the board. The grounding strap will prevent static electricity from accumulating.

Walking and touching items can cause static electricity to accumulate so it is best practice to not move too much before you work with the board. When you do handle the board only hold it by the edges and never touch the solder points or the components. Just before you are ready to install it remove it from the package and touch it to a unpainted metal surface to drain off any static. Only then is it safe to install the replacement board.

If you have to put down the board after removing it from the bag, only place it on top of the empty static-protective bag.

The capacitors on the DS200SDCIG2AEB can store high-voltage current even after the current is removed, so it is important to test the board for current before you touch it, so as to prevent electrical burns and shocks.

Frequently Asked Questions about DS200SDCIG2AEB

Which manual is used with DS200SDCIG2AEB?

The manual used with DS200SDCIG2AEB is the GE Drive Systems Replacement Procedures for SDCI DC Power Supply and Instrumentation Board Manual. Although this manual is a manual based on replacing DS200SDCIG2AEB with another DS200SDCIG2AEB board, the manual provides additional information to help you understand DS200SDCIG2AEB.

What is the JP2 jumper used for on DS200SDCIG2AEB?

The JP2 jumper on DS200SDCIG2AEB is the MA AC contactor drop-out time jumper for DS200SDCIG2AEB. Generally, this circuit on DS200SDCIG2AEB delays opening of the AC contactor to ensure all load current has been extinguished on DS200SDCIG2AEB. Removing jumper JP2 on DS200SDCIG2AEB during normal running can cause the control-on circuit to drop out the MA relay before the current is at 0.