DS200RTBAG2AFB GE 板和涡轮控制

部件编号ds200rtbag2afb

系列mark V DS200

制造商通用电气板和涡轮控制

功能缩写rtba

功能描述中继终端板

分组变异g2

电源24vdc

继电器编号k20 - k26和K27-K29

联系电话：18059884797

立即咨询在线留言

产品详情

DS200RTBAG2AFB GE 板和涡轮控制

【功能描述】

DS200RTBAG2AFB技术规格

部件编号ds200rtbag2afb

系列mark V DS200

制造商通用电气板和涡轮控制

功能缩写rtba

功能描述中继终端板

分组变异g2

电源24vdc

继电器编号k20 - k26和K27-K29

产品描述

DS200RTBAG2AFB是为通用电气Mark V板系列设计的继电器端子板(RTBA)。该板可用于多个GE品牌驱动器和励磁器的应用。通过将该板安装到驱动柜中，向用户提供了额外的十个继电器。LAN I/O终端和远程用户都可以驱动这块板上的继电器。

位置K20至K29是所有板载继电器的电路板位置。DS200RTBAG2AFB包括两种继电器，DPDT和4PDT。DPDT类型包括卡上的七个继电器，包括K20到K26。这些类型具有两个C型触点，每个触点额定10A。K27到K29是第二种继电器类型，4PDT。而不是两个，4PDT继电器包括四个形式C触点，每个速率1A。所有这些点都由130 VAC金属氧化物压敏电阻(MOV)保护。每个继电器包含一个内部110 VDC线圈，以确保它们正常运行。如果任何继电器停止工作或断开，用户可以很容易地拆卸和更换所有十个点。

DS200RTBAG2AFB型号有两个连接器;一个是16针连接器，另一个是两针连接器。16针连接器被标记为RPL，两针连接器被标记为OPTPL。OPTPL连接器有两个命名X2和CFX1。X2命名法将信号发送回CFX1命名法120vac负载的NTB/3TB板。此命名法与RPL X2命名法相同。有关这两个连接器的所有可用命名，请参阅GEI-10016B手册中的表3和表4。

DS200RTBAG2AFB常见问题

在DS200RTBAG2AFB型号上使用时，十六针(RPL)连接器中的每个引脚都连接吗?

不。RPL连接器上一致连接的引脚是引脚1、3、5、7、9、11、13和15。每个引脚都有单独的命名法和单独的描述。例如，引脚13被称为RX6命名法。RX6术语描述为RTBA模型上继电器K25的LTB导频输入。有关其他术语和描述，请参阅GEI-100167B手册第5页的表3。

DS200RTBAG2AFB型号上有多少个终端可用?

DS200RTBAG2AFB型号上有52个终端可用。每个终点都有自己的命名法和描述。命名和描述的一个例子是终点27。27号端子上的命名法是K232CM，描述继电器K23形式C接触数2。有关所有术语、端点和描述的更多信息，请参阅GEI-100167手册。

DS200RTBAG2AFB GE 板和涡轮控制

DS200RTBAG2AFB technical specification

Part number ds200rtbag2afb

Series mark V DS200

Manufacturer General Electric board and turbine controls

Function abbreviation rtba

Function Description Trunk terminal board

Group mutation g2

Power supply 24vdc

Relay numbers k20-k26 and K27-K29

Product description

The DS200RTBAG2AFB is a relay terminal board (RTBA) designed for the General Electric Mark V board series. The board can be used in applications with multiple GE branded drives and exciters. By mounting the board into the drive cabinet, an additional ten relays are provided to the user. Both LAN I/O terminals and remote users can drive the relays on this board.

Positions K20 to K29 are circuit board locations for all onboard relays. The DS200RTBAG2AFB includes two relays, DPDT and 4PDT. The DPDT type consists of seven relays on the card, including K20 to K26. These types have two C-type contacts, each rated at 10A. K27 to K29 is the second relay type, 4PDT. Instead of two, 4PDT relays include four form C contacts at a rate of 1A each. All of these points are protected by 130 VAC metal-oxide varistors (MOV). Each relay contains an internal 110 VDC coil to ensure their proper operation. If any of the relays stop working or break, the user can easily remove and replace all ten points.

The DS200RTBAG2AFB model has two connectors; One is a 16-pin connector and the other is a two-pin connector. 16-pin connectors are labeled RPL and 2-pin connectors are labeled OPTPL. OPTPL connectors have two designations X2 and CFX1. The X2 nomenclature sends the signal back to the CFX1 nomenclature for the NTB/3TB board with a 120vac load. This naming is the same as the RPLX2 naming. Refer to Tables 3 and 4 in the GEI-10016B manual for all available designations for these two connectors.

DS200RTBAG2AFB Frequently Asked Questions

Is every pin in the sixteen pin (RPL) connector connected when used on DS200RTBAG2AFB models?

Nooooo. The consistently connected pins on the RPL connector are pins 1, 3, 5, 7, 9, 11, 13, and 15. Each pin has a separate nomenclature and a separate description. For example, pin 13 is called the RX6 nomenclature. The RX6 term describes the LTB pilot input of relay K25 on the RTBA model. For additional terms and descriptions, see Table 3 on page 5 of the GEI-100167B manual.

How many terminals are available on the DS200RTBAG2AFB model?

52 terminals are available on the DS200RTBAG2AFB model. Each endpoint has its own nomenclature and description. An example of naming and describing is endpoint 27. The nomenclature on terminal 27 is K232CM, describing the relay K23 form C contact number 2. For more information on all terms, endpoints, and descriptions, see the GEI-100167 manual.