DS200LDCCH1AGA 驱动控制/局域网通讯板

部件编号ds200ldcch1aga

系列mark V

制造商ge通用电气

使用说明书gei -100216

驱动控制/局域网通讯板

功能缩写/缩写ldcc

跳线数14

联系电话：18059884797

立即咨询在线留言

产品详情

DS200LDCCH1AGA 驱动控制/局域网通讯板

【功能描述】

DS200LDCCH1AGA技术规范

部件编号ds200ldcch1aga

系列mark V

制造商ge通用电气

使用说明书gei -100216

驱动控制/局域网通讯板

功能缩写/缩写ldcc

跳线数14

重量约2磅

产品描述

通用电气开发了DS200LDCCH1AGA卡作为驱动控制和局域网(LAN)通信板。该卡安装在Mark V系列替代驱动板中，与GE品牌DIRECTO-MATIC 2000驱动器和励磁器兼容。当安装在驱动器中，该板为驱动器提供驱动器阵列和I/O控制功能。

DS200LDCCH1AGA通信卡上有四个微处理器。局域网控制处理器(LCP)可用于接受五种不同的总线类型馈送到驱动器。驱动控制处理器(DCP)也可用于处理模拟和数字I/O转换。DCP还能够控制和转换外围I/O设备，如编码器和定时器。电机控制处理器(MCP)用于处理发送到驱动器的数字I/O。如果计算需要DCP无法提供的额外处理能力，则协同电机处理器(CMP)将提供完成这些功能所需的额外功率。该板由一个用于系统编程和诊断目的的字母数字键盘完成。

DS200LDCCH1AGA模型具有现场可调参数;其中之一是EEPROM U9，它将被编程为下载正确操作LDCC单元所需的驱动器配置值。EEPROM U9固件可以通过从另一个驱动控制板移动U9直接传输到LDCC单元。

DS200LDCCH1AGA常见问题

DS200LDCCH1AGA提供什么类型的驱动器?

DS200LDCCH1AGA为通用电气的Directo-Matic 2000驱动器和励磁器提供主驱动器和I/O控制功能。

DS200LDCCH1AGA模型上的一些测试点及其定义是什么?

该模型的一些测试点是P5, DCOM1/DCOM2和FCLK。P5测试点用于帮助调节5伏电源。测试点DCOM1/DCOM2将控制用于所有测试信号的0伏公共参考点。FCLK测试点表明该单元是活的，并且根据需要，8 MHz输出来自电机控制器处理器的振荡器输出。对于所有其他的测试点，请参考LDCC手册第五页的表1。

我应该使用DS200LDCCH1AGA的哪个手册?

带DS200LDCCH1AGA，使用Manual GEI-100216。本手册DS200LDCCH1AGA是通用电气电机和工业系统驱动控制/局域网通信板手册。虽然这不是DS200LDCCH1AGA的全面安装、操作和维护手册，但本手册将帮助您了解DS200LDCCH1AGA。

DS200LDCCH1AGA 驱动控制/局域网通讯板

DS200LDCCH1AGA technical specification

Part number ds200ldcch1aga

Series mark V

Manufacturer ge General Electric

Instruction Manual gei-100216

Drive control/LAN communication board

Function abbreviation/abbreviation ldcc

Number of jumpers 14

It weighs about 2 pounds

Product description

Ge developed the DS200LDCCH1AGA card as a driver control and local area network (LAN) communication board. The card is installed in the Mark V Series replacement driver board and is compatible with GE brand DIRECTO-MATIC 2000 drives and exciters. When installed in a drive, the board provides the drive array and I/O control functions for the drive.

The DS200LDCCH1AGA communication card has four microprocessors. The local Area Network Control Processor (LCP) can be used to accept five different bus types of feeds to the drive. The Drive Control Processor (DCP) can also be used to handle analog and digital I/O conversions. DCP is also able to control and convert peripheral I/O devices such as encoders and timers. The motor control processor (MCP) is used to process the digital I/O sent to the drive. If the computation requires additional processing power that a DCP cannot provide, the co-motor processor (CMP) will provide the additional power needed to accomplish these functions. The board is completed by an alphanumeric keyboard for system programming and diagnostic purposes.

DS200LDCCH1AGA model has field adjustable parameters. One of these is the EEPROM U9, which will be programmed to download the drive configuration values needed to properly operate the LDCC unit. EEPROM U9 firmware can be transferred directly to the LDCC unit by moving the U9 from another drive control board.

DS200LDCCH1AGA Common problems

What type of drive does the DS200LDCCH1AGA provide?

The DS200LDCCH1AGA provides master drive and I/O control functions for General Electric's Directo-Matic 2000 drives and exciter.

What are some test points and their definitions on the DS200LDCCH1AGA model?

Some test points for this model are P5, DCOM1/DCOM2, and FCLK. The P5 test point is used to help regulate the 5 volt power supply. The test point DCOM1/DCOM2 will control the 0 volt common reference point for all test signals. The FCLK test point indicates that the unit is alive and, as needed, the 8 MHz output comes from the oscillator output of the motor controller processor. For all other test points, refer to Table 1 on page 5 of the LDCC manual.

Which manual of DS200LDCCH1AGA should I use?

With DS200LDCCH1AGA, use Manual GEI-100216. This manual DS200LDCCH1AGA is a General Electric motor and industrial systems Drive control/LAN communication board manual. Although this is not a comprehensive installation, operation and maintenance manual for the DS200LDCCH1AGA, this manual will help you understand the DS200LDCCH1AGA.