DS200SDCCG1 驱动控制卡 具有电机控制处理器

DS200SDCCG1 技术指标

制造者 通用电气通用电气

系列 马克五世

部件号 DS200SDCCG1

产品类型 驱动控制卡

产品描述

通用电气驱动控制板DS200SDCCG1是驱动器的主控制器。 GE驱动控制板DS200SDCCG1装有3个微处理器和RAM，可由多个微处理器同时访问。您可以将卡安装在通用电气驱动控制板DS200SDCCG1上以增加功能。一张卡提供 LAN 通信，另外两张卡扩展了板的信号处理能力。卡通过电缆连接到主板。

但是，更换DS200SDCCG1电路板时必须考虑以下事项。在安装更换板之前，首先必须从有缺陷的板上卸下卡，然后将其安装在更换板上。将更换板放在保护袋顶部的平坦表面上以安装卡。同时，您可以检查有缺陷的电路板，并确保更换板上的所有跳线设置完全相同。

同时，握住电路板的边缘并将电缆连接到更换板。如果将电缆从有缺陷的板上直接插入更换板，这将变得更加容易和快捷。或者，您可以在断开电缆连接之前标记电缆。考虑到DS200SDCCG1电路板包含的配置设置存储在电路板上的四个 EPROM 芯片上。要将有缺陷的电路板的配置转移到更换电路板，请将EPROM逐个从有缺陷的电路板移动到新电路板。

The General Electric Drive Control Board DS200SDCCG1 is the main controller of the driver. The GE drive control board DS200SDCCG1 is equipped with three microprocessors and RAM, which can be accessed by multiple microprocessors simultaneously. You can install the card on the General Electric Drive Control Board DS200SDCCG1 to add functionality. One card provides LAN communication, while the other two cards extend the board's signal processing capabilities. Connect the card to the motherboard through a cable.

However, the following considerations must be considered when replacing the DS200SDCCG1 circuit board. Before installing a replacement board, the card must first be removed from the defective board and then installed on the replacement board. Place the replacement board on a flat surface at the top of the protective bag to install the card. At the same time, you can check for defective circuit boards and ensure that all jumper settings on the replacement board are identical.

At the same time, hold the edge of the circuit board and connect the cable to the replacement board. If the cable is directly inserted into the replacement board from the defective board, it will become easier and faster. Alternatively, you can label the cable before disconnecting it. Considering that the configuration settings contained in the DS200SDCCG1 circuit board are stored on four EPROM chips on the circuit board. To transfer the configuration of a defective circuit board to a replacement circuit board, move the EPROM one by one from the defective circuit board to the new circuit board.

关于DS200SDCCG1的常见问题

DS200SDCCG1 由什么组成？

DS200SDCCG1 由三个 16 位微处理器和相关电路组成，通过双端口 RAM 耦合。DS200SDCCG1还具有接口电路，可与其他电路板连接，形成各种类型的交流和直流电机驱动器。

DS200SDCCG1的接口电路有什么作用？

DS200SDCCG1 上的接口电路控制和处理驱动器和电机信号以及客户 I/O。

DS200SDCCG1 的主要微处理器是什么？

DS200SDCCG1 有三个主要的微处理器。DS200SDCCG1 具有驱动控制处理器。DS200SDCCG1 具有电机控制处理器。DS200SDCCG1 具有协电机处理器。