DS200RTBAG1AEB 中继端子板 与Mark V Speedtronic系统配合使用

DS200RTBAG1AEB 中继端子板  与Mark V Speedtronic系统配合使用

品牌/制造商：

制造商零件编号：DS200RTBAG1AEB

附加信息： 电路板

条件： 新

可用性： 30

保证： 12 个月

估计重量： 0.8 千克

原产国： 美国

航运： 全球由 DHL /联邦快递 /TNT / 不间断电源提供

产品描述

GE的DS200RTBAG1AEB PCB是与通用电气的Mark V Speedtronic系统配合使用的组件。 Mark V是Speedtronic工业涡轮控制系统的复杂版本之一。这些系统（Mark I 到 Mark VI）专为工业蒸汽和燃气轮机的管理、保护和控制而设计。

DS200RTBAG1AEB可以安装在GE驱动柜或励磁器中。 这是一个可选的板。安装后，DS200RTBAG1AEB为系统增加了<>个额外的继电器。继电器通常由位于LTB I/O端子板上的先导继电器驱动。或者，它们可以由用户远程驱动。DS200RTBAG1AEB是一个 110 VDC 板。如果您需要 24VDC 或 115 VAC 的 RTBA 板，请参阅我们的 RTBAG2 和 RTBAG3 板列表。

DS200RTBAG1AEB是一块又长又窄的电路板。它在工厂钻入或靠近每个角落。电路板的中心由十个继电器占据。每个继电器都有一个 LED 指示灯，用于指示其何时通电。这些继电器由位于元件侧面的金属氧化物压敏电阻保护。DS200RTBAG1AEB板有许多连接点。这包括用于可插拔电路控制电源的卡入式连接器、用于 C 型触点和线圈电压源的接线端子，以及多个插头和引脚连接器。此外，该板具有 15 个 berg 型跳线，用于控制线圈电压源、外部电源和可插拔电路

GE's DS200RTBAG1AEB PCB is a component used in conjunction with General Electric's Mark V Speedtronic system. The Mark V is one of the complex versions of the Speedtronic industrial turbine control system. These systems (Mark I to Mark VI) are designed specifically for the management, protection, and control of industrial steam and gas turbines.

DS200RTBAG1AEB can be installed in GE drive cabinets or exciters. This is an optional board. After installation, DS200RTBAG1AEB added<>additional relays to the system. The relay is usually driven by a pilot relay located on the LTB I/O terminal board. Alternatively, they can be remotely driven by the user. The DS200RTBAG1AEB is a 110 VDC board. If you need an RTBA board with 24VDC or 115 VAC, please refer to our list of RTBAG2 and RTBAG3 boards.

DS200RTBAG1AEB is a long and narrow circuit board. It drills into or near every corner of the factory. The center of the circuit board is occupied by ten relays. Each relay has an LED indicator light to indicate when it is powered on. These relays are protected by metal oxide varistor located on the side of the element. The DS200RTBAG1AEB board has many connection points. This includes plug-in connectors for pluggable circuit control power supplies, wiring terminals for C-type contacts and coil voltage sources, as well as multiple plug and pin connectors. In addition, the board has 15 Berg type jumpers for controlling coil voltage sources, external power supplies, and pluggable circuits