IS200TRLYH1D  |   IS200VAICH1DAB  |  电路板(PCB)

型号:IS200TRLYH1D

类别:电路板(PCB)

交货时间:从现货开始

结束:新的，不是新的

快递:顺丰、德邦

隔离电压:1000V)

准确性:±0.5%)

工作温度范围:-40℃~ 85℃)

电源电压:请填写电源电压范围(如9V至36V)

功耗:0.5W)

尺寸:100mm × 50mm × 25mm)

重量:150g)

接口类型:DIN导轨安装)

IS200TRLYH1D是GE为Mark VI系统制造的电路板(PCB)。MKVI专为启动时的速度控制而设计，是GE发布的最后一批“Speedtronic”系统之一。Mark VI在正常运行期间提供涡轮机负载控制，并在失去负载的情况下保护涡轮机超速。MKVI还提供自动发电机同步。该系统设计用于管理大型和小型涡轮机应用，可以设计为TMR(三模冗余)系统或单工形式。

IS200TRLYH1D作为具有电磁完整性传感的继电器输出端子板。这块电路板有六个插入式磁继电器。这些电路是c型触点输出，通过熔断和供电来驱动外部螺线管。坏的螺线管可以通过在每个继电器电路上提供的特殊反馈来检测。

IS200TRLYH1D类似于TRLYH1B板。然而，该板只有六个继电器，仅为24/125V直流应用而设计。继电器不能配置为干接点使用，输入继电器线圈监控已被移除。该单板通常由VCRC或VCCC单板控制。它支持TMR或单工应用程序。

Model: IS200TRLYH1D

Category: Circuit Board (PCB)

Delivery time: from stock

Finish: New, not new

Express: SF Express, Deppon

Isolation voltage: 1000V)

Accuracy :±0.5%)

Operating temperature range: -40°C to 85°C)

Power supply voltage: Please fill in the power supply voltage range (e.g. 9V to 36V)

Power consumption :0.5W)

Size :100mm x 50mm x 25mm)

Weight: : 150g)

Interface type: DIN rail mounting)

The IS200TRLYH1D is a board (PCB) manufactured by GE for the Mark VI system.   Designed for speed control during startup,  the MKVI is one of the last “Speedtronic” systems released by GE.   The Mark VI offers turbine load control during  normal operation and protection against turbine overspeed in situations where there is a loss of load.   The MKVI also  offers automatic generator synchronization.  The system is designed to manage both large turbine applications and small  ones and can be designed either as a TMR (triple modular redundant) system or in Simplex form.

The IS200TRLYH1D functions as a Relay Output terminal board with Solenoid Integrity Sensing.   This board has six plug-in  magnetic relays.  These circuits are Form-C contact outputs that are fused and powered to drive external solenoids.   Bad  solenoids can be detected through special feedback provided on each relay circuit.

The  IS200TRLYH1D is similar to a TRLYH1B board.   However,  this board has only six relays and is designed for 24/125V dc applications only.   The relays cannot be configured for  dry contact use,  and input relay coil monitoring has been removed.  The board is typically controlled by the VCRC or VCCC board.  It  supports either TMR or simplex applications.