IC694BEM321  |   IC694MDL250  | IC694MDL330 | 控制器模块

型号：IC694BEM321

类别：控制器模块

成色：全新/非全新

货期：现货

质保：一年

快递：顺丰/德邦

付款：电汇， 西联汇款

GE Fanuc IC694BEM321 PACSystems RX3i 控制器模块被设计为由多达 16 个连接的 I/O 从模块组成的 I/O Link 网络中的主模块。使用单个GE Fanuc IC694BEM321 PACSystems RX3i控制器模块，可以监控多达1024个独立输入的状态，并通过1024个独立输出发送响应，以控制实施系统的应用过程或机器。该主模块的安装过程与任何其他GE Fanuc模块的安装过程相同。它可以插入 GE 90-30 系列 PLC 背板或 GE RX3i 系统的任何可用插槽中。

GE Fanuc IC694BEM321 PACSystems RX3i 控制器模块数量可安装在单个网络中的唯一先决条件是网络必须能够为连接的设备提供所有必要的电源。每个设备都由 PLC 或 RX3i 背板供电，每个设备都需要 5 伏直流电才能正常工作。从模块通过RS485或RS422串行协议串联连接。GE Fanuc IC694BEM321 PACSystems RX3i 控制器模块在前保护盖内有一个串行端口，因为它只需要连接到第一个从站处理器。其余的处理器以菊花链形式一个接一个地连接。用于此 I/O Link 网络的电缆连接器带有 20 个引脚，称为本田型连接器。模块的运行状态可以通过放置在设备前部顶部的 3 个 LED 进行验证。

IC694BEM321 | IC694MDL250 | IC694MDL330 | Controller module

Model: IC694BEM321

Category: Controller module

Finish: New/not new

Delivery time: from stock

Warranty: One year

Express: SF Express/Debon

Payment: Wire transfer, Western Union

The GE Fanuc IC694BEM321 PACSystems RX3i controller module is designed to be the master module in an I/O Link network consisting of up to 16 connected I/O slave modules. With a single GE Fanuc IC694BEM321 PACSystems RX3i controller module, it is possible to monitor the status of up to 1024 independent inputs and send responses through 1024 independent outputs to control the application process or machine that implements the system. The installation process for this master module is the same as for any other GE Fanuc module. It can be inserted into any available slot on the GE 90-30 series PLC backplane or GE RX3i system.

GE Fanuc IC694BEM321 Number of PACSystems RX3i Controller Modules The only prerequisite that can be installed in a single network is that the network must be able to provide all the necessary power to the connected devices. Each unit is powered by a PLC or RX3i backplane, and each requires 5 volts of direct current to function properly. The slave module is connected in series via RS485 or RS422 serial protocol. The GE Fanuc IC694BEM321 PACSystems RX3i controller module has a serial port in the front protective cover, as it only needs to be connected to the first slave processor. The rest of the processors are connected one by one in a Daisy chain. The cable connector for this I/O Link network comes with 20 pins and is called a Honda type connector. The operating status of the module can be verified by three leds placed on the top of the front of the device.