IC695DEM008| IC695GCG001 |  IC695MDL664 | 以太网接口模块

型号：IC695DEM008

类别：以太网接口模块

成色：全新/非全新

质保：一年

输出数量、类型和速度#N/A

输出额定值#N/A

电流消耗#N/A

机构UL、UL HAZLOC

批准区域 2 CE、ATEX C1D2 ABS、BV、DNV、GL、KRS、LR

媒体支持铜、MM和SM光纤

安装方式在面板/DIN导轨上

介绍

以太网接口模块IC695DEM008用于将PACSystems RX3i控制器连接到以太网。它

使RX3i控制器能够与其他PACSystems设备以及90系列和VersaMax进行通信

控制器。以太网接口提供传输控制协议和TCP/iP (internet Protocol)协议。

与其他控制系统、运行编程软件的主机和运行程序的计算机之间的通信

TCP/lP版本的编程软件。这些通信使用服务请求传输协议

(SRTP)、Modbus TCP和以太网全局数据(EGD)协议通过四层TCP/iP(互联网)堆栈。

RX3i以太网接口的特点包括:

编程和配置服务。通过Web/HTTP方式从RX3i CPU升级固件

如果CPU支持该方法，或者通过使用WinLoader软件实用程序，它提供了更新

以太网接口软件。

使用以太网全局数据(EGD)进行周期性数据交换。

EGD通过网络读写控制器和EGD交换内存的命令

使用SRTP的fCP/IP通信服务。

支持SRTP通道，Modbus/TCp服务器和Modbus/TCp客户端

型号面板上的以太网接口，用于直接连接到模块。

3个自传感10BaseT/100BaseTX/1000BaseTX R|45个屏蔽双绞线以太网端口

无需外部收发器即可连接到10BaseT或100BaseTX或1000T lEEE 802.3网络。

有一个网络接口用于通信协议和站管理器(两个端口)和一个

单独的接口(一个端口)仅供站点管理器访问。

内部网络交换机与自动协商，感测，速度，和交叉检测。

“以太网重启”按钮允许手动重启以太网固件，而不需要重新启动

系统。

led: OK, STATUS, LAN OK, LOG EMPTY，单个端口活动和速度led。

可配置独立冗余IP寻址，允许分配单个IP地址

对应的以太网模块在两个不同的控制器。已配置“冗余iP地址”

除了每个以太网模块正常唯一的lP地址之外。在应用程序逻辑控制下，只有

主用单元的以太网模块可以使用冗余地址。

时间同步到以太网的SNTp时间服务器(当使用5.00或更高版本的CPU时)

模块)。

IC695DEM008| IC695GCG001 |  IC695MDL664  | Ethernet interface module

Model: IC695DEM008

Category: Ethernet interface module

Finish: New/not new

Warranty: One year

Output quantity, type, and speed #N/A

Output rating #N/A

Current consumption #N/A

Organization UL, UL HAZLOC

Approved Area 2 CE, ATEX C1D2 ABS, BV, DNV, GL, KRS, LR

The media supports copper, MM, and SM optical fibers

Mounting on panel /DIN rail

introduce

Ethernet interface module IC695DEM008 is used to connect the PACSystems RX3i controller to Ethernet. it

Enables RX3i controllers to communicate with other PACSystems devices as well as the 90 Series and VersaMax

The controller. Ethernet interfaces provide Transmission control Protocol and internet Protocol (TCP/iP).

Communication with other control systems, hosts running programming software, and computers running programs

TCP/lP version of programming software. These communications use the Service Request Transport Protocol

(SRTP), Modbus TCP, and Ethernet Global Data (EGD) protocols pass through the Layer 4 TCP/iP(Internet) stack.

Features of the RX3i Ethernet interface include:

Programming and configuring services. Upgrade firmware from the RX3i CPU via Web/HTTP

If the CPU supports this method, or by using the WinLoader software utility, it provides updates

Ethernet interface software.

Periodic data exchange using Ethernet Global Data (EGD).

EGD reads and writes memory commands between the controller and EGD over the network

fCP/IP communication services using SRTP.

Support SRTP channels, Modbus/TCp servers and Modbus/TCp clients

Ethernet interface on the model panel for direct connection to the module.

3 since the sensing 10 baset basetx / 100/1000 basetx R | 45 shielded twisted-pair Ethernet port

Connect to 10BaseT or 100BaseTX or 1000T lEEE 802.3 networks without an external transceiver.

There is a network interface for the communication protocol and station manager (two ports) and one

A single interface (one port) is accessible only to the site manager.

Internal network switches with automatic negotiation, sensing, speed, and cross detection.

The Ethernet Restart button allows you to manually restart the Ethernet firmware without the need for a reboot

System.

led: OK, STATUS, LAN OK, LOG EMPTY, single port activity and speed led.

Independent redundant IP addressing can be configured, allowing a single IP address to be assigned

The corresponding Ethernet modules are in two different controllers. Redundant iP Addresses have been configured.

In addition to the normal unique lP address for each Ethernet module. Under application logic control, only

The Ethernet module of the primary unit can use redundant addresses.

Time synchronization to an Ethernet SNTp time server (when using a 5.00 CPU or later)

Module).