型号:IC693DSM302-AE
类别:两轴运动控制模块
发货方式::顺丰/联邦
汇款:电汇/西联
控制电源 :标称 25 VA,最大 35 VA
绝缘电压: 300 伏
通信协议: Modbus RTU 或 DNP 3.0
数据记录存储 :2 到 16 个事件,分别有 2048 到 256 个数据样本
波形捕获采样率: 每个周期 16 个
产品描述
IC693DSM302-AE 模块是一个两轴运动控制模块,它是高度集成的逻辑求解和
lC693 PLC的通信功能,提供两种主要控制回路配置:标准模式和Follower模式。DSM302的基本功能如下:
数字信号处理器(DSP)提供ge发那科交流伺服的矢量控制伺服回路更新:250 ussec(扭矩),1 mSec(速度),2 mSec(位置)块处理时间在5毫秒以下速度前馈和位置误差积分器,提高跟踪精度编程单元的高分辨率
8.388.608…+8,388.607用户单位
位置:
速度:
1……8,388,607用户单位/秒
加速度:1…134.217.727用户单位/秒/秒
易用性
简单而强大的指令集
IC693DSM302-AE 具有同步块启动的单轴或双轴运动程序
程序支持可以在MS-DOS中创建的短运动程序(称为程序零)
编程软件组态功能
10个程序和40个子程序的非易失性(闪存)存储器
用户扩展编程单元(仅在标准模式下)
使用命令参数作为加速、速度、移动和驻留的操作数的通用编程
命令配置了MSDOS配置软件
Model: IC693DSM302-AE
Category: Two-axis motion control module
Delivery method: SF Express/Federal
Remittance: Wire transfer/Western Union
Control power supply: nominal 25 VA, maximum 35 VA
Insulation voltage: 300 volts
Communication protocol: Modbus RTU or DNP 3.0
Data record storage: 2 to 16 events with 2048 to 256 data samples
Waveform capture sampling rate: 16 per cycle
Product description
The IC693DSM302-AE module is a two-axis motion control module that is highly integrated with logic solvers and
The communication function of the lC693 PLC offers two main control loop configurations: standard mode and Follower mode. The basic functions of the DSM302 are as follows:
The digital signal processor (DSP) provides ge Fannuc AC servo with vector control servo loop updates :250 ussec(torque), 1 mSec(speed), 2 mSec(position) block processing time at speeds below 5 milliseconds with feedforward and position error integrators, improving tracking accuracy for high resolution programming units
8.388.608... +8,388.607 User units
Location:
Speed:
1... 8,388,607 User units per second
Acceleration :1... 134.217.727 User unit/s/s
Ease of use
Simple yet powerful instruction set
The IC693DSM302-AE features single - or biaxial motion programs initiated by synchronous blocks
Program support for short motion programs (called program zeros) that can be created in MS-DOS
Programming software configuration function
Non-volatile (flash) memory for 10 programs and 40 subroutines
User Extended Programming unit (only in standard mode)
General-purpose programming that uses command parameters as operands for acceleration, speed, movement, and residence
Command to configure the MSDOS configuration software
Copyright © 2022-2024 厦门雄霸电子商务有限公司 版权所有 备案号:闽ICP备14012685号-33