IC200CPU005 |  IC695CPU310  支持多达64个模块，最多2048个L0点

型号：IC200CPU005

特征

支持多达64个模块，最多2048个L0点

可以由程序员自动西置西管er

使用组态次4

用于应用程序的64KB可配置内存,m

硬件配置,g寄存器(%R)，模拟输入(%AI)。)

和模拟输出(%AQ)

榜形图和指表的编术

用子程序存储的非易失性闪存

用子程序，数据和白天时钟时间的电池备份

超级电容器为存储器提供1小时的能量。

超过1小小时cku备用电池保护内存内容。p

到6个月s.

备用电池不使用时，保质期为5年.se.

运行/停止开关

浮点实教据阿娄女

支持EZ程序存储设备(LC200ACC003)

在DLN钢轨:安装电源时高度为70毫米

IC200CPU005 操作注意事项/限制

1.在扩展机架中使用较旧版本的非智能模拟模块将导致记录系统配置不匹配错误。在扫描出现故障的模块之前，必须用较新的修订版本替换该模块。允许的修订在上面的产品信息部分的兼容性下有详细说明。

2.IC200CPU005 如果在IND或ISA PID回路中使用积分项，应避免PID积分值小于0.002。以下示例措述使用小于0.002的整数值时的行为:

假设SP=16000，PV=16000，CV=16000，P=1.00，1=1.000。D=0.00

若将整数项降为0.002;CV不变

若积分项为0.001,CV将降至其原始值(8000)的一半

若整数项为0.000，则CV降至0。在这一点上，没有积分贡献。

3.如果在CPU上电时，本地单个机架中的接收器关闭，则CPU可能会记录错误的"机架添加"故障。建议CPU和接收器都由一个电源供电。

4.偶尔，在对主或扩展机架进行电源循环后，智能Vo模块上可能会记录“背板通信故障”。这是一个可以消除的诊断故障。

5.在非常罕见的情况下，当一个模块上失去磁场电源时。同一机架中的非智能模块也可能报告故障。

6.在非常罕见的情况下，IC200CPU005 被热插入的模块可能不会被CPU添加它不会产生“模块添加”错误，也不会被扫描。可以通过提取和重新插入模块来纠正这种情况。

7.在非常罕见的情况下，热插入模块可能会导致同一机架中的模拟模块将输出设置为零。除此之外，““模块丢失

Model: IC200CPU005

trait

Supports up to 64 modules and up to 2048 L0 points

The west tube er can be automatically inserted by the programmer

Use configuration times 4

64KB of configurable memory for applications,m

Hardware configuration,g register (%R), analog input (%AI).

And analog output (%AQ)

Compilation of charts and finger tables

Nonvolatile flash memory stored by a subroutine

Battery backup with subroutines, data and daytime clock time

Supercapacitors provide energy for memory for one hour.

cku backup battery protects memory contents for more than 1 hour. p

By 6 months s.

When the spare battery is not in use, the shelf life is 5 years.se.

Run/stop switch

Floating point real teaching according to Alou female

Support EZ program storage device (LC200ACC003)

On DLN rail: 70 mm height when power is installed

IC200CPU005 Operation Precautions/Restrictions

1. Using an older version of the non-intelligent analog module in the extension rack will result in a mismatch error in the logging system configuration. Before scanning a failed module, the module must be replaced with a newer revision. The permitted revisions are detailed under Compatibility in the Product Information section above.

2.IC200CPU005 If the integral term is used in the IND or ISA PID loop, avoid PID integral value less than 0.002. The following example illustrates the behavior when using an integer value less than 0.002:

Suppose SP=16000, PV=16000, CV=16000, P=1.00, 1=1.000. D = 0.00

If the integer item is reduced to 0.002; CV invariance

If the integral term is 0.001,CV is reduced to half of its original value (8000)

If the integer is 0.000, CV drops to 0. At this point, there is no point contribution.

3. If the receiver in a single local rack is turned off while the CPU is powered on, the CPU may record an incorrect "rack Add" fault. It is recommended that both the CPU and the receiver be powered by one power supply.

4. Occasionally, after power cycling to the main or extension rack, a "backplane communication failure" may be recorded on the smart Vo module. This is a diagnostic fault that can be eliminated.

5. In very rare cases, when a magnetic field power is lost on a module. Non-intelligent modules in the same rack may also report failure.

6. In very rare cases, IC200CPU005 hot-inserted modules may not be added by the CPU. It will not produce a "module add" error and will not be scanned. This can be corrected by extracting and reinserting the module.

7. In very rare cases, a hot-insert module may cause an analog module in the same rack to set the output to zero. Apart from that, "the module is missing