IS220PAICH1B | 模拟输入/输出包  |  端子板

型号：IS220PAICH1B

输入电压范围:12-48VDC

输出电压范围:5VDC。

输出电流:最大10A。

效率:大于90%。

尺寸:170mm x105mmx32mm.

重量:约120g。

运行温度:-20°C至+50°C。

存储温度:-40°C至+70°C。

环境湿度:5%至95%相对湿度(无凝露)

产品描述

IS220PAICH1B型号由通用电气生产，是Mark VI系列的模拟输入/输出包。该型号是PAIC单元的第二个版本，与先前版本的PAIC单元相比，其最小电压不同。该特定装置的最小电压为 22 伏半直流电。此型号使用的标称电源是 24 或 28 伏直流电。

虽然 Mark VI 系列中使用了 IS220PAICH1B 包，但它可以与某些附件（也称为端子板）一起使用;与此特定模拟 I/O 包一起使用的接线板都是 IS200 板，并且是 IS200TBAIH1C、IS200TAIH1A 和 IS200TAIH2A。IS200TBAIH1C 型号是屏障型接线盒，在与 IS220PAICH1B 组连接和使用时，要求最小电线尺寸为 22 AWG。

使用此型号时会出现特定的警报，其中一个警报标记为 82-83，它专注于输出并指示IS220PAICH1B包内的自杀继电器不起作用。此警报的可能原因通常是包中的自杀继电器命令与相关反馈不匹配、硬件出现故障或采集板上发生继电器故障。此问题的主要解决方案是更换 I/O 包本身。

IS220PAICH1B包可用于许多不同的场所，包括危险和非危险场所，根据该型号的非危险场所认证为 UL E207685。

Model: IS220PAICH1B

Input voltage range :12-48VDC

Output voltage range :5VDC.

Output current: Max. 10A.

Efficiency: greater than 90%.

Size :170mm x105mmx32mm.

Weight: About 120g.

Operating temperature :-20°C to +50°C.

Storage temperature :-40°C to +70°C.

Ambient humidity :5% to 95% relative humidity (no condensation)

Product description

The IS220PAICH1B model is manufactured by General Electric and is an analog input/output package for the Mark VI series. This model is the second version of the PAIC unit with a different minimum voltage compared to the previous version of the PAIC unit. The minimum voltage for this particular device is 22 volts of semi-direct current. The nominal power supply used in this model is 24 or 28 volts DC.

Although the IS220PAICH1B package is used in the Mark VI series, it can be used with certain accessories (also known as terminal boards); The patch boards used with this particular analog I/O package are all IS200 boards and are IS200TBAIH1C, IS200TAIH1A, and IS200TAIH2A. The IS200TBAIH1C model is a barrier junction box that requires a minimum wire size of 22 AWG when connected and used with the IS220PAICH1B group.

Specific alarms appear when using this model, one of which is labeled 82-83, which focuses on the output and indicates that the suicide relay inside the IS220PAICH1B package is not working. The possible cause of this alarm is usually a mismatch between the suicide relay command in the package and the relevant feedback, a hardware failure, or a relay failure on the acquisition board. The main solution to this problem is to replace the I/O package itself.

The IS220PAICH1B package can be used in many different sites, both hazardous and non-hazardous sites, and is certified as UL E207685 according to the non-hazardous site for this model.